Tennant T5 Скачать руководство пользователя страница 63

Страница: 63 / 68

Rev 00

Indicates Maximum Throttle

Indicates Throttle

is in Forward Po

sition

Indicates Throttle

is in Reverse Position

Indicates Throttle

is in Neutral Position

Indicates Throttle

position betw

Minimum and Maximum

Indicates Minimu

m Throttle

Fault LED’s 1, 2,

and 3 Indicate th

e sensed level

of the Speed Lim

it Potentiometer.

No Fault LED’s

ON = 30

% of Ma

ximum Propel

Voltage

Fault LED 1

>= 40% of Ma

ximum Propel

Voltage.

Fault LED’s 1 an

d 2 ON >= 66

of Maximum

Propel Voltage.

Fault LED’s 1,2,

and 3 ON = 100

% of Ma

ximum

Propel Voltage

Battery

gauge L

D’s display

the

throttle

output voltage.

INDICATOR

THR

TLE V

LTA

LED #1 (red) =

< 2.2V.

LED#2 (amb

er)

= > 2.2 and < 2.4

LED #3 (g

reen

) is lit w

hen the th

rottle

voltage is > 2.4 and < 2. 6V.

LED #4 (g

reen

)

= > 2.6 and < 2.8

LED #5 (g

reen

)

= > 2.8V.

To Enter Pro

pel Dia

gno

stics M

ode, sim

ultaneo

usly h

old the (-

) De

cre

ase Wate

r and (+) Incre

ase

wn Pressure button

s on

power up.

te: Th

e Prop

el Motor is d

isabled in Propel Diagno

stics Mod

The Down Pressure LED’

s indicate the t

rottle position, reverse, ne

utral, or forwa

rd. Wh

en the

bail is not a

tivated, Down

Pressu

re LE

D #2 an

d Battery LED #3 (gree

sho

uld

be lit. This indi

cate

s that the throttle is i

the cente

r p

sition a

nd th

at t

controller is sensi

ng Neutral.

The Solution

Level LED’

s indicate the sensed po

sitio

n of the throttle potentiomet

er between M

in and Max in forward or

reverse.

The Fault LE

D’s in

dicate the se

nsed po

sition of the Speed Limit Po

tentiometer (t

he sp

eed

con

trol on the pa

nel).

itch

T5 –Propel Diagnostics Mode

T5 9002333 REV.0

(07-06)

Содержание T5





































































Результаты поиска

Содержание T5

Отзывы:

Tennant T5, Руководство по эксплуатации, Страница: 63 / 68

Результаты поиска

Содержание T5

Отзывы: