Tennant T5 Скачать руководство пользователя страница 25

Страница: 25 / 68

CONTROL PANEL FAULT INDICATOR CODES

The control panel fault indicator lights will display the following codes when the machine detects a fault.

Light #1

Light #2

Light #3

Light #4

Battery Lights

CODE

FAULT

SOLUTION

Light #1 blinks

Recovery tank is raised.

Lower recovery tank. Restart key to reset.

Lights #1, #2 and #3
ripple

Battery charger connected.

Disconnect battery charger. Restart key to
reset.

Lights #1 and #4 blink

Left Brush motor overload.

Inspect brush for entangled debris,
improper pad or contact service center.
Restart key to reset.

Lights #3 and #4 blink

Right Brush motor overload.

Inspect brush for entangled debris,
improper pad or contact service center.
Restart key to reset.

Lights #2 and #3 blink

Propel motor overload.
Exceeded maximum incline.

Avoid steep inclines or contact service
center. Restart key to reset.

Lights #1 and #3 blink

Scrub head movement is obstructed or
actuator motor malfunction.

Check scrub head for obstruction or con-
tact service center. Restart key to reset.

Light #2 blinks

Vacuum motor malfunction.

Contact Tennant Service 1-800-553-8033

Lights #1 and #2 blink

Propel throttle malfunction.

Contact Tennant Service 1-800-553-8033

Light #3 blinks

FaST pump overload or malfunction.

Reset the 10A circuit breaker or contact
service center. Restart key to reset.

Light #3 blinks when
pressing the solution flow,
brush pressure buttons
and FaST system switch

Supervisor controls activated
(lockout feature)

Contact your Supervisor.

Lights #1, #2 and #3 blink

Wand Pump overload or malfunction.

Reset the 10A circuit breaker button or
contact service center. Restart key to
reset.

All battery lights blink

Emergency--Stop button activated

Turn button clockwise to reset.

All battery lights ripple

Key turned on while bail was engaged.

Release the control handle start bail.

T5 –

Maintenance

(Page 15 of 15)

T5 9002333 REV.0

(07-06)

Содержание T5





































































Результаты поиска

Содержание T5

Отзывы:

Tennant T5, Руководство по эксплуатации, Страница: 25 / 68

Результаты поиска

Содержание T5

Отзывы: