Tennant T5 Скачать руководство пользователя страница 56

Страница: 56 / 68

Rev 00

One Step But

ton

Indicates Month (One’s)

Indicates the Month (Te

n’s)

Indicates the Da

y (Ten’s)

Indicates

the Year (One’s)

Indicates the Da

y (One’s)

Indicates the Year (Ten’s)

Holdi

ng the O

ne Step button on Power-up puts you int

o the software

revisio

n display mode. T

he numb

er of

blinks by the Do

wn Pre

re and

Water level LED’s represents the software revision.

The Hig

st Pressu

re (te

’s) & wate

r le

vel (one’s) n

bers blin

kin

g together

pre

sent

s the month.

The Middl

e Pressu

re (te

n’s) & water leve

l (one’s) n

bers blin

king

together

rep

rese

nts the da

The Lo

w Pre

ssure

(ten’

& water level

(one’

s) numb

rs bli

nki

ng togethe

r re

pre

sent

s the year.

No blin

king of

an LED mea

ns zero. Fo

exampl

e if the high pressure LED does not blink a

the high wate

r LED blin

ks six times,

that means the

month is

JUNE. Also if the

Middle Pre

ssure LE

D blin

ks twice and the Middle water blinks once, that means the day is the 21

Note: The

sof

tware

revisi

on LED will continue to blink until the ma

chine is turned off.

rnK

T5 – Display Software Revision Mode

(Page 1 of 2)

T5 9002333 REV.0

(07-06)

Содержание T5





































































Результаты поиска

Содержание T5

Отзывы:

Tennant T5, Руководство по эксплуатации, Страница: 56 / 68

Результаты поиска

Содержание T5

Отзывы: