manualshive.com logo in svg

Tennant T5, Руководство по эксплуатации, Страница: 55 / 68

Поделиться
Скачать
Tennant T5 Скачать руководство пользователя страница 55

T5 – Diagnostic & Configuration Modes

Mode

Entry Sequence

Indicator

Function

Upper Brush Pressure LED blinks Tens of days 
of month, Upper Solution Flow LED blinks Single 
day of month

Middle Brush Pressure LED blinks Tens of 
month, Middle Solution Flow LED blinks Single 
month

Lower Brush Pressure LED blinks Tens of year, 
Lower Solution Flow LED blinks out Single year

Self Test        

Mode

 Press and hold Increase Solution 
Flow (+) and Decrease Brush 
Pressure (-) Buttons, turn key 
switch ON, wait 10 seconds, 
release buttons

Start of test - Both Scrub Brush motors run          
End of test - LED's indicate system pass or fail

Solid lit One Step LED indicates OK,  A 
Flashing LED indicates an OPEN Fault, A 
Solid lit LED (other than One Step) indicates 
a SHORT Fault (Refer to Self Test Mode 
page for more information)

Input Display 

Mode

Press and hold Decrease Solution 
Flow (-) Button, turn key switch 
ON, release button after forth 
battery LED starts to blink

LED's will indicate the the state of the control 
board inputs

Shows state of control board inputs from 
various switches and sensors (Refer to Input 
Display Mode pages for more information)

Manual Mode

Press and hold Decrease Brush 
Pressure (-) Button, turn key 
switch ON, release after Lowest 
Brush Pressure LED starts to 
blink.

Lowest down pressure LED will blink

Allows operation of individual functions 
without the safety interlocks affecting or 
controlling them (Refer to Manual Mode 
pages for more information)

Propel 

Diagnostics 

Mode

Press and hold Decrease Solution 
Flow (-) and Increase Brush 
Pressure (+) Buttons, turn key 
switch ON, release after One Step 
LED starts to blink

Battery Gauge LED's indicate position of throttle

Provides information regarding throttle input 
signal and propel motor current (Refer to 
Propel Diagnostics Mode page for more 
information)

Battery Select 

Mode

Press and hold the Increase 
Solution Flow (+) Button, turn key 
switch ON, release after one 
Battery LED starts to blink

Any one of lower 4 Battery Gauge LED’s blinks

Allows selection of battery type (Refer to 
Battery Select Mode page for more 
information)

Battery LED #3 (Green) flashing - Supervisor 
mode enabled

Battery LED #1 (Red) flashing - Supervisor 
mode disabled

Scrub Propel 

Speed Selection 

Mode

Press and hold Increase Brush 
Pressure (+) Button, turn key 
switch ON, release after selecting 
desired Brush Pressure LED 
setting

Brush Pressure Lower, Middle, and Upper LED’s 
represents LOW, MEDIUM and HIGH maximum 
Forward Scrubbing Propel Speed selection

Allows selection of maximum forward speed 
during scrubbing                                    
LOWER (#1) LED = 150 ft/min                       
MIDDLE (#2) LED = 200 ft/min                       
UPPER (#3) LED = maximum speed             
(Refer to Scrub Propel Speed Selection 
Mode page for more information)

Scrub Head 

Selection Mode

Press and hold Decrease Solution 
Flow (-) and Decrease Brush 
Pressure (-) Buttons, turn key 
switch ON, release after one 
Brush Pressure LED and one 
Solution Flow LED is lit. To 
change setting, press & hold One 
Step Button until it blinks, then 
press the Brush Pressure (+) 
Button or Solution Flow (+) Button 
to change setting.

Lower Brush Pressure LED (#1) – Disk
    -Lower Solution Flow LED (#1) – 24”
    -Middle Solution Flow LED (#2) – 28”
    -Upper Solution Flow LED (#3) – 32”
Middle Brush Pressure LED (#2) – Cylindrical
    -Lower Solution Flow LED (#1) – 26”
    -Upper Solution Flow LED (#3) – 32"

Allows machine to be configured for various 
scrub heads (Refer to Scrub Head Selection 
Mode page for more information)

Display Software 

Revision Mode

Press and hold One Step Button, 
turn key switch ON, wait 10 
seconds, release One Step Button

Blinking Brush Pressure and Solution Flow 
LED’s indicate revision date (Refer to 
Display Software Revision Mode page for 
more information)   

Supervisor Mode

Press and hold Increase Solution 
Flow (+) and Increase Brush 
Pressure (+) Buttons, turn key 
switch ON, release after battery 
LED 1 or 3 starts to blink

Toggle Supervisor Mode.  When enabled, 
the scrub mode settings are disabled and 
Fault LED #3 is lit. If Solution Flow or Brush 
Pressure buttons are pressed, Fault LED #3 
will blink. (Refer to Supervisor Mode page 
for more information)

T5  9002333  REV.0

2

  (

11

-07)

51

E

Содержание T5





































































Отзывы:

Нет отзывов