Tennant T5 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 68

Tennant T5 Скачать руководство пользователя страница 4

BEFORE CONDUCTING TESTS:

z

Read and Follow ALL Safety Warnings and Precautions in Operator's

Manual

z

Always use an ESD (Electrostatic Discharge) strap when working near

the Control Board

z

Be cautious when working near Control Board –

Battery voltage is

always present, even with Key OFF

z

Always Disconnect Batteries when removing or replacing components

DURING TESTS:

z

Call Technical Services if Diagnostic Time Exceeds One Hour with

Unknown Cause or Course of Action

!

T5

Service Information Manual

iv

T5 9002333 REV.0

2

(

11

-07)

!

IMPORTANT INFORMATION FOR MACHINES WITH SERIAL
NUMBER DATE CODES PRIOR TO DC1006 (October, 2006)

Potential rolling hazard may exist when transporting the machine on a ramp or incline with key
turned to the “off” position. The machine could roll at an undesirable speed creating the risk for
potential injury or property damage.

To ensure operator safety and to prevent potential property damage,Tennant Company mandates
that the existing control box assembly be replaced with the Control Box Kit (p/n 9003250). For more
information, refer to Technical Service Bulletin # 130. To determine if the machine in question has
been updated with the new Control Box Kit, refer to the picture below.

CONTROL BO

X ASSEMBLY

If the Brake Relay (CR2) is present in the
Control Box, the machine has already been
updated and no further action is required.
If the Brake Relay (CR2) is NOT present in
the Control Box, follow the instructions in
Technical Service Bulletin # 130.

CR2

«
...
2
3
4
5
6
...
»

Содержание T5





































































Отзывы:

Нет отзывов