Tennant 365 Скачать руководство пользователя страница 78

Страница: 78 / 102

MAINTENANCE

365 MM173 (3---90)

3-36

BELTS AND CHAINS

ALTERNATOR BELT (For machines below serial

number 007000)

The alternator belt is driven by the engine crankshaft

sheave and drives the water pump and alternator

sheaves. Check and adjust the alternator belt

tension after every 200 hours of operation.

To tighten the alternator belt, loosen the alternator

mounting bolts and pull the alternator away from the

engine until the belt is snug; then tighten the bolts.

Do not use a pry bar on the alternator as it will

damage the alternator. Proper belt tension is

obtained when the belt deflects 0.09 in (2 mm) from

a force of 7 to 10 lb (3 to 4.5 kg) applied at the

midpoint of the longest span.

03769

BELTS

A. Engine Fan Belt

B. Alternator Belt

ENGINE FAN BELT (For machines below serial

number 007000)

The engine fan belt is driven by the engine

crankshaft sheave and drives the engine fan and

governor sheaves. Check and adjust the engine fan

belt tension after every 200 hours of operation.

To tighten the engine fan belt, loosen the governor

mounting bolts, pull the governor away from the

engine until the belt is snug, then tighten the bolts.

Proper belt tension is obtained when the belt deflects

0.25 in (6 mm) from a force of 1 to 2 lb (0.5 to 0.9 kg)

applied at the midpoint of the longest span. After

adjusting the belt check the governor adjustment as

described in

TO ADJUST GOVERNOR (For machines

below serial number 007000)

ENGINE FAN BELT (For machines serial number

007000 and above)

The engine fan belt is driven by the engine

crankshaft sheave and drives the engine fan and

alternator. Check and adjust belt tension after every

100 hours of operation.

To adjust belt tension, loosen the alternator mounting

bolts and pull the alternator away from the engine

until the belt is snug; then tighten the bolts. Do not

use a pry bar on the alternator as it may damage the

alternator. Proper belt tension is obtained when the

belt deflects 0.5 in (13 mm) from a force of 8 to 10 lb

(4 to 5 kg) applied at midpoint of the longest span.

STATIC DRAG CHAIN

A static drag chain is provided to prevent the buildup

of static electricity in the machine. The chain is

attached to the machine by a rear brush skirt

retaining bolt.

The chain should make contact with the floor at all

times.

Содержание 365







































































































Результаты поиска

Содержание 365

Отзывы:

Бренды по названию

Популярные бренды

Tennant 365, Руководство оператора

Результаты поиска

Содержание 365

Отзывы:

Бренды по названию

Популярные бренды