manualshive.com logo in svg

Tennant 365, Руководство оператора

Поделиться
Скачать
Tennant 365 Скачать руководство пользователя страница 52

MAINTENANCE

365 MM173 (3---90)

3-10

5. Add hydraulic fluid until the level in the reservoir

is between the “ADD” and the “FULL” range. Do

not overfill.

NOTE: Do not overfill the hydraulic fluid reservoir. As

hydraulic fluid heats to its normal operating

temperature, it expands. Always allow for this

expansion when filling the hydraulic fluid reservoir.

6. Place the reservoir breather-filler cap securely

on the reservoir filler neck.

7. Lower the operator seat.

8. Start engine and operate all of the hydraulic

components. Then recheck the hydraulic fluid

level.

HYDRAULIC FLUID RESERVOIR BREATHER

The hydraulic fluid reservoir is equipped with a

breather. The breather relieves excess atmospheric

pressure or vacuum in the reservoir. The breather is

mounted on the hydraulic fluid reservoir filler neck

located under the operator seat. The breather should

be replaced after every 800 hours of operation.

A

B

02160

RESERVOIR BREATHER-FILLER CAP

A. Filler Neck

B. Breather-Filler Cap

HYDRAULIC FLUID FILTER

The machine hydraulic system is kept clean to a

level of 10 microns by a hydraulic fluid filter. The

hydraulic fluid filter is located in the left front of the

machine engine compartment.

Replace the hydraulic fluid filter element after the first

50 hours of operation and then after every 400 hours

of operation.

TO REPLACE HYDRAULIC FLUID FILTER ELEMENT

1. Stop the engine and set the machine parking

brake.

FOR SAFETY: Before leaving or servicing

machine; stop on level surface, set parking brake,

and turn off machine.

2. Open the side engine access door.

A

B

02166

HYDRAULIC FLUID FILTER

A. Hydraulic Fluid Filter Element

B. Engine

3. Unthread and discard the hydraulic fluid filter

element.

NOTE: Discard all hydraulic fluid drained from the

system. Drained hydraulic fluid may contain foreign

material harmful to the hydraulic system.

4. Apply a thin coat of hydraulic fluid to the seal of

the new hydraulic fluid filter element.

5. Thread and hand tighten the new hydraulic

fluid filter element on the filter head.

6. Operate the machine and check for leaks.

Correct any leaks found.

7. Check the hydraulic fluid reservoir level and fill

as required.

8. Close the side engine access door.

Содержание 365







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды