Tennant 365 Скачать руководство пользователя страница 39

Страница: 39 / 102

OPERATION

2-19

365 MM173 (3---90)

TRANSPORTING MACHINE

PUSHING OR TOWING MACHINE

The machine may be pushed from the front or the

rear, using the bumpers provided, only after placing

the rear wheel on a dolly.

The machine may be towed in either direction after

placing the rear wheel on a dolly. Do not pull on the

front bumper --- pull on the hopper pivot tube.

ATTENTION! Do not push or tow the machine

without placing the rear wheel on a dolly; the

machine hydraulic system may be damaged.

03765

FRONT TOW LOCATION

A. Hopper Pivot Tube

MACHINE JACKING

The machine may be jacked up for service at the

designated locations. Use a jack of adequate

capacity and good working condition. Always stop

the machine on a flat, level surface and block the

tires before jacking the machine up. The front

jacking locations are on the flat bottom edge of the

machine frame in front of the front tires.

The rear jacking location is the middle flat bottom

edge of the rear bumper.

TO JACK UP MACHINE

1. Empty the debris hopper.

2. Stop the engine and set the machine parking

brake.

FOR SAFETY: Before leaving or servicing

machine; stop on level surface, set parking brake,

and turn off machine.

3. Block the tires, which are not being jacked up,

in order to secure the machine position.

WARNING: Machine is unstable on jack.

Block machine tires before jacking machine

up.

4. Use a jack of adequate capacity to raise the

machine. Jack up the machine only at the

designated locations.

WARNING: Machine is unstable on jack.

Jack machine up at designated locations

only. Block machine up with jack stands.

02141

FRONT JACKING LOCATION

A. Jacking Location

03764

REAR JACKING LOCATION

A. Jacking Location

Содержание 365







































































































Результаты поиска

Содержание 365

Отзывы:

Похожие инструкции для 365

Бренды по названию

Популярные бренды

Tennant 365, Руководство оператора

Результаты поиска

Содержание 365

Отзывы:

Похожие инструкции для 365

Бренды по названию

Популярные бренды