manualshive.com logo in svg

TENEO LoRaWAN CO2 stoplicht, Руководство пользователя

Поделиться
Скачать
TENEO LoRaWAN CO2 stoplicht Скачать руководство пользователя страница 18

 

 
Manual LoRaWAN CO

2

 stoplicht 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

18 

© 

Copyright 

2021 

Teneo 

Sales 

BV. 

                  [email protected] 

All rights reserved.    

 

 

All information in this manual Is subject to change without further notice.

 

   

 

 

+31 (0)543 535 535 

 

 

Humidity display: 
 
This bit indicates whether the humidity is given, if it is set to 0 together with temperature display, the uplink 
will be 4 bytes shorter. 
 
If it is at 0 but temperature at 1, then the humidity sent will always be 0xFFFF. 
 
Bit 1 = 1: control humidity. 
Bit 1 = 0: Do not control humidity. 
 
Temperature display: 

 

This bit indicates whether the humidity is given, if it is set to 0 together with temperature display, the uplink 
will be 4 bytes shorter. 
 
If it is at 0 but humidity at 1, then the controlled temperature will always be 0x7FFF. 
 
Bit 0 = 1: control the temperature. 
Bit 0 = 0: Do not send temperature. 

 

Payload: 0x03(binary:00000011): 

temperature 

and humidity aresent

 

along with the CO2 value.

 

 

FPort 11: LED borders Green/Orange/Red: 

 

Byte  

Length 

Description 

Default V1.20:  Default V1.30: 

0..1 

2 

Minimum value green

 

0x0000 

0x0000 

2..3 

2 

Maximum value green

 

0x041A 

0x03E8 

4..5 

2 

Minimum value orange

 

0x041B 

0x03E9 

6..7 

2 

Maximum value orange

 

0x060D 

0x0578 

8..9 

2 

Minimum value red

 

0x060E 

0x0579 

10..11 

2 

Maximum value red 

0xFFFF 

0xFFFF 

 

Here the limit values of the green/orange/red LEDs can be set, if the CO

2

 

measurement is equal or between these 2 

values, the corresponding LED will turn on

 

*

.

 

 

If both values of a certain LED are set to 0, the LED will never be on.

 

The example below uses the default values.

 

Example: 
Payload 0x0000 03E8

 

03E9 0578

 

0579 FFFF: 

 

* This setting only has an effect if the LED indicator in the behavior setting is turned on see "

FPort 13 Behavior Settings

". 

 
FPort 12: Automatic and manual calibration 

 
 

Byte number 

Length  Description 

0 

1* 

Automatic calibration on/off 

0..2 

3* 

Manual calibration incl. reference value of manual 
calibration in ppm 

 
* The length of this downlink is 1 byte when automatic calibration is turned on or off and 3

 

bytes when manual 

calibration is used. 

 

Содержание LoRaWAN CO2 stoplicht





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды