manualshive.com logo in svg

TENEO LoRaWAN CO2 stoplicht, Руководство пользователя

Поделиться
Скачать
TENEO LoRaWAN CO2 stoplicht Скачать руководство пользователя страница 11

 

 
Manual LoRaWAN CO

2

 stoplicht 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11 

© 

Copyright 

2021 

Teneo 

Sales 

BV. 

                  [email protected] 

All rights reserved.    

 

 

All information in this manual Is subject to change without further notice.

 

   

 

 

+31 (0)543 535 535 

 

 

5.1. In advance 

 
In this document, all bits are read as "Little-endian". This means that all bits are read from right to left. 
Bytes are read from left to right. Both bytes and bits start from the number 0. 

 

Example with the decimal number 279716668: 
 
In hexadecimal: 
 
Byte 0          Byte 3 
     |              | 
0x10 AC 23 3C 
 
Binary: 
 
Bit7   Bit0  Bit7    Bit0 Bit7  Bit0  Bit7    Bit0 
|             |   |             |  |             |  |             | 
00010000 10101100 00100011 00111100 
 

5.1.1. Definitions: 

 

  Node: The device with the microcontroller developed by Teneo. 

  Uplink: A message from the node to the LoRaWAN network. 

  Downlink: A message from the LoRaWAN network to the node. 

  Payload: The data sent or received by the node. 

  0xA3: The hexadecimal number A3, decimal is 163 and binary this is 1010 0011. 

  Unsigned int: A positive integer. 

  Int: An integer (positive or negative). 

  RFU: Reserved For Future Use. 

  Float: A decimal number (positive and negative). 

 

5.2. Firmware versions 

 
Since the launch of the CO

2

 stoplicht, several firmware improvements have been made. 

The following is a table with a brief overview of the different firmware versions, the release date of this 
firmware and a brief description of the changes/improvements.  
 

Firmware version:  Release date: 

Content: 

V1.10 

19-11-2020 Initial 

release/launch. 

 

V1.20 

17-12-2020 

Improved measurement of temperature and humidity.  

V1.30 

21-01-2021 

Automatic calibration default enabled 
Manual calibration option added 
Added downlinks for setting air pressure and altitude above 
sea level 
Default thresholds LEDs adjusted(green: up to 1000 ppm, 
orange: 1001 to 1400 ppm,red: 1401 ppm or higher).  

 

5.3. Uplinks 

 
Uplink messages from a Teneo LoRaWAN sensor consist of two components: the port and the payload.  
Each uplink payload starts with one header byte. 
 

5. Payload

Содержание LoRaWAN CO2 stoplicht





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды