manualshive.com logo in svg

TENEO LoRaWAN CO2 stoplicht, Руководство пользователя

Поделиться
Скачать
TENEO LoRaWAN CO2 stoplicht Скачать руководство пользователя страница 16

 

 
Manual LoRaWAN CO

2

 stoplicht 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16 

© 

Copyright 

2021 

Teneo 

Sales 

BV. 

                  [email protected] 

All rights reserved.    

 

 

All information in this manual Is subject to change without further notice.

 

   

 

 

+31 (0)543 535 535 

 

For example, at value 0x0753: is binary: 

0

001 0001 0100 1101, last bit is 

0

 so: 

0x0753 = decimal 1875: the temperature = 1875/100 = 18.75 degrees Celsius. 
 
For example, at value 0xFCE0: is binary: 

1

111 1100 1110 0000, last bit is 

1

 so: 

0xFCE0 = decimal 64736: temperature = -(65536-64736)/100 = -8.00 degrees Celsius. 
 

Measured Humidity: 

 

Byte number 

Length  Description 

8..9 

2 Humidity 

display 

 
This byte shows the measured humidity display. To convert this to the actual value, this calculation must be 
used: 
 
Humidity %RH = Humidity display/100 
 
For example, the display = 0x114D = 4429. 
Humidity = 4429/100 = 44,29 %RH. 
 

5.4. Downlinks 

 
In order to change the settings of the node, downlinks can be sent to the node. As with the uplinks, the 
FPort indicates what type of message it is, but no header needs to be sent. 
 
The following downlinks can be sent: 
 

FPort  Message type 

From version:  Description 

1 

Period time 

V1.10 

Adjusts the time between two standard downlink 
messages. 

8 

Air pressure 
compensation 

V1.30 

An air pressure compensation for the CO

2

 

measurements, expressed in millibar. 

9 

Height compared to sea 
level compensation 

V1.30 

The height of the CO

2

 stoplicht specified for the 

CO

2

 sensor for compensation relative to the sea 

level, expressed in meters. 

10 

Display temperature/ 
humidity 

V1.30 

Setting for displaying temperature, humidity or 
both.  

11 

LED Borders 
Green/Orange/Red 

V1.10 

Specify the limit values for when the red, orange, 
and green LEDs should turn on/off. 

12 

Automatic and manual 
calibration 

V1.30 

Turning the automatic calibration and/or manual 
calibration function of the CO

2

 sensor on/off.  

13 

Settings behavior 

V1.10 

Setting whether the LEDs should be used 

 
In the table above, version indicates 

from

 which firmware version this downlink is incorporated into the CO

2

 

stoplicht. So when it says "V1.10" here, this means that this downlink can be used at all stoplichts with 
V1.10 or newer. When "V1.30" is displayed here, this means that this downlink can be used at all stoplichts 
with V1.30 or newer.  
 
 
 
 
 
 
 

Содержание LoRaWAN CO2 stoplicht





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды