background image

20

21

    7.2.4. Detail

  You can use Detailed Screen to observe a specific zone.

  The basic setting information will be shown on the bottom of the screen and 
the screen will show the operation status of controller with Digital Number 
and [16 zones] will be displayed on zone selection button on the right side.

 

  7.3. Setting display

① Setting item name: 

This is the place that displayed name of setting item.

② Display setting value: 

It will display setting value for set up.

③ No setting value: 

It will display [- -] when there is no setting or no selection of 

zone.

④ Difference of setting value: 

It will display [ * * ] when setting values are different 

if you choose several zones.

⑤ Page change of setting screen: 

This is the button that change setting screen of 

[basic setup], [Advanced setup 1] and [Advanced setup 2]. You can set up Advance 

setup when “Lock Mode” is released only.

⑥ Zone Selection Button1: 

When you click the button, it is selected and when you 

click the button again, it is released.

⑦ Zone Selection Button2: 
Select All ☞ 

Click when you select the entire zone.

Release All ☞ 

Click when you release the entire zone.

Select nozzle ☞

 When you click this option, zone that set as nozzle is selected and 

when you click this option again, zone that set as nozzle is released.

Select Manifold ☞ 

When you click this option, zone that set as Manifold is selected 

and when you click this option again, zone that set as Manifold is released.

    7.3.1. Basic setting display

③Set Temp

②Present Temp

⑤Consumption current

④Output Percent

①Zone No

Содержание TC-3200 Lite






























Отзывы: