Telit Wireless Solutions SL876Q5-A Скачать руководство пользователя страница 43

Страница: 43 / 68

SL876Q5-A

Product User Guide

1VV0301333 Rev. 2

Page 43 of 68

2017-06-27

Use the Query/Rate Control (

PSRF103

) to enable and disable output NMEA messages and

set their output rates.

After configuration, the pins are defined below:

Pin Name UART Function

Primary Port

Transmit Data (TX)

Receive Data (RX)

GPIO6

nCTS

GPIO7

nRTS

Secondary Port

TX1

Transmit Data (TX1)

RX1

Receive Data (RX1)

Table 8-11 UART Pin Assignments

Note: Flow control is disabled by default.

Use the

OSP MID 178,70

command to enable/disable flow control on the first port.

C Operation

See

Section 8.8.1 Primary Host Port

Configuration to specify I

C interface. Upon power up,

the module acts as a master transmitter and a slave receiver (multi-master mode).

•

When used in I

C mode, pull-ups in the range of 1K to 2.2K to a 1.8V to 3.6V power

supply are required on the RX and TX lines.

Clock rates of 100 and 400 kbps are supported.

The operation of the I

C with a master transmit and slave receive resembles a UART operation,

where both the module and the host can independently freely transmit. It is possible to enable
the master transmit and slave receive at the same time, as the I

C bus allows for contention

resolution between module and host vying for the bus.

Содержание SL876Q5-A





































































Результаты поиска

Содержание SL876Q5-A

Отзывы:

Похожие инструкции для SL876Q5-A

Бренды по названию

Популярные бренды

Telit Wireless Solutions SL876Q5-A, Руководство пользователя

Результаты поиска

Содержание SL876Q5-A

Отзывы:

Похожие инструкции для SL876Q5-A

Бренды по названию

Популярные бренды