Telit Wireless Solutions SL876Q5-A Скачать руководство пользователя страница 5

Страница: 5 / 68

SL876Q5-A

Product User Guide

1VV0301333 Rev. 2

Page 5 of 68

2017-06-27

CONTENTS

NOTICE

. .................................................................................................... 2

COPYRIGHTS ................................................................................................ 2

COMPUTER SOFTWARE COPYRIGHTS ...................................................... 2

USAGE AND DISCLOSURE RESTRICTIONS ............................................... 3

PRODUCT APPLICABILITY TABLE .............................................................. 4

INTRODUCTION ........................................................................ 11

Purpose ...................................................................................... 11

Contact and Support Information ................................................ 11

Text Conventions ........................................................................ 12

Related Documents .................................................................... 13

Related Documents Requiring a Non-disclosure Agreement ....... 13

PRODUCT DESCRIPTION ......................................................... 14

Product Overview ....................................................................... 14

SL876Q5-A Block Diagram ......................................................... 15

SL876Q5-A Module .................................................................... 16

SL876Q5-A EVALUATION KIT (EVK) ....................................... 17

SL876Q5-A Evaluation Board (EVB) ........................................... 18

PRODUCT FEATURES .............................................................. 19

Built-in Antenna and Switch ........................................................ 19

Multi-Constellation Navigation ..................................................... 19

Quasi-Zenith Satellite System (QZSS) support ........................... 19

Satellite Based Augmentation System (SBAS) ............................ 19

SBAS Corrections ....................................................................... 19

SBAS Ranging ............................................................................ 19

Assisted GPS (AGPS) - SiRFInstantFix™ ................................... 19

Client-generated Extended Ephemeris (CGEE) .......................... 20

Server-generated Extended Ephemeris (SGEE) ......................... 20

2-D Positioning ........................................................................... 20

Static Navigation ......................................................................... 20

Velocity Dead-Reckoning ............................................................ 21

Jamming Rejection – Continuous Wave (CW) Jamming Mitigation21

Elevation Mask Angle ................................................................. 21

5 Hz Navigation .......................................................................... 21

10 Hz Navigation ........................................................................ 22

Содержание SL876Q5-A





































































Результаты поиска

Содержание SL876Q5-A

Отзывы:

Похожие инструкции для SL876Q5-A

Бренды по названию

Популярные бренды

Telit Wireless Solutions SL876Q5-A, Руководство пользователя

Результаты поиска

Содержание SL876Q5-A

Отзывы:

Похожие инструкции для SL876Q5-A

Бренды по названию

Популярные бренды