Telit Wireless Solutions SL876Q5-A Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 68

background image

SL876Q5-A

Product User Guide

1VV0301333 Rev. 2

Page 63 of 68

2017-06-27

GPS

Global Positioning System
The U.S. GNSS, a satellite-based positioning system that provides
accurate position, velocity, and time data. GPS is operated by the US
Department of Defense.

Hot Start

A hot start occurs when a receiver begins operation with known time,
position, and ephemeris data, typically after being sent a restart command.
See Restart.

LCC

Leadless Chip Carrier
A module design without pins. In place of the pins are pads of bare gold-
plated copper that are soldered to the printed circuit board.

LNA

Low Noise Amplifier
An electronic amplifier used for very weak signals which is especially
designed to add very little noise to the amplified signal.

Local Ephemeris
prediction data

Extended Ephemeris (i.e. predicted) data, calculated by the receiver from
broadcast data received from satellites, which is stored in memory. It is
usually useful for up to three days. See AGPS.

MSAS

MTSAT Satellite Augmentation System
The Japanese SBAS system.

MSD

Moisture sensitive device.

MTSAT

Multifunctional Transport Satellites
The Japanese system of geosynchronous satellites used for weather and
aviation control.

Navigation Sensitivity

The lowest signal level at which a GNSS receiver is able to reliably
maintain navigation after the satellite signals have been acquired.

NMEA

National Marine Electronics Association

QZSS

Quasi-Zenith Satellite System
The Japanese SBAS system (part of MSAS).

Reacquisition

A receiver, while in normal operation, loses RF signal (perhaps due to the
antenna cable being disconnected or a vehicle entering a tunnel), and re-
establishes a valid fix after the signal is restored. Contrast with Reset and
Restart.

Restart

A receiver beginning operation after being sent a restart command,
generally used for testing rather than normal operation. A restart can also
result from a power-up. See Cold Start, Warm Start, and Hot Start.
Contrast with Reset and Reacquisition.

Reset

A receiver beginning operation after a (hardware) reset signal on a pin,
generally used for testing rather than normal operation. Contrast with
Restart and Reacquisition.

RoHS

The Restriction of Hazardous Substances
Directive on the restriction of the use of certain hazardous substances in
electrical and electronic equipment, was adopted in February 2003 by the
European Union.

RTC

Real Time Clock
An electronic device (chip) that maintains time continuously while powered
up.

SAW

Surface Acoustic Wave filter
Electromechanical device used in radio frequency applications. SAW
filters are useful at frequencies up to 3 GHz.

«
...
61
62
63
64
65
...
»

Содержание SL876Q5-A





































































Отзывы:

Нет отзывов

Похожие инструкции для SL876Q5-A

Бренд: ZETRON Страницы: 3

Бренд: Caen Страницы: 20

Бренд: Quectel Страницы: 95

Бренд: ICAS Страницы: 51

Бренд: Icar Страницы: 40

Бренд: Icar Страницы: 86

Бренд: Icar Страницы: 39

Бренд: IBP Страницы: 12

Бренд: Watts Страницы: 12

Бренд: Lancom Страницы: 8

Бренд: YUGE Страницы: 69

Бренд: Quectel Страницы: 232

Бренд: Quectel Страницы: 9

Бренд: Quectel Страницы: 73

Tissue-Tek TEC 6

Бренд: Sakura Seiki Страницы: 6

Бренд: Panasonic Страницы: 8

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: IBA Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды