Telit Wireless Solutions ME310G1-W1 Скачать руководство пользователя страница 69

Страница: 69 / 96

ME310G1 Hardware Design Guide

1VV0301588 Rev. 12

Page 69 of 96

2021-06-14

Recommendations for ME310G1-WW, ME310G1-WWV,
ME310G1-W2 and ME310G1-W3

In order to easily rework the ME310G1-WW, ME310G1-WWV, ME310G1-W2 and ME310G1-
W3 it is recommended to consider the application placement inhibit area around the
module, as specified in the below figure.

It is also suggested, as common rule for an SMT component, to avoid having a mechanical
part of the application in direct contact with the module.

Figure 18: ME310G1-WW, ME310G1-WWV, ME310G1-W2 and ME310G1-W3 Recommendations

Note: In the customer application, the region under WIRING
INHIBIT (see the figure above) must be clear from signal or ground
paths.

Содержание ME310G1-W1

































































































Результаты поиска

Содержание ME310G1-W1

Отзывы:

Похожие инструкции для ME310G1-W1

Бренды по названию

Популярные бренды

Telit Wireless Solutions ME310G1-W1, Руководство по конструкции аппаратуры

Результаты поиска

Содержание ME310G1-W1

Отзывы:

Похожие инструкции для ME310G1-W1

Бренды по названию

Популярные бренды