background image

FIRE

R M LD

FIRE

R M LD

Operator’s Manual

30

GAS LASER

Doc No. 16162 Rev A, GAS LASER Operator Manual 

© 2021 Teledyne Gas Measurement Instruments Ltd. All rights reserved.

Maintenance

Warranty and Repair

In order to maintain the Gas Laser in good working condition, the following 
maintenance should be performed as indicated:

Maintenance Item

Frequency

Clean outer surfaces with damp rag

As needed

Clean instrument window with damp Kim-

Wipe™ or equivalent non-abrasive lens tissue

As needed to prevent dust or water stain 

build up

Self Test

Daily to ensure the instrument is functioning 

properly

Recharge battery pack

Recharge to full capacity after each use

Replace battery pack

As needed

When storing a battery pack for one month 

or more leave a storage capacity

As needed

Instruments and products manufac-
tured by Heath Consultants Incorpo-
rated are warranted to be free from 
defects in material and workman-
ship for one (1) year from the date 
of shipment.

Furthermore, the warranty on 
authorized repairs in the Houston 
Factory Service Center (FSC) and 
other regions is ninety (90) days 
materials and thirty (30) days labor. 
This repair warranty does not extend 
any other applicable warranties.

Warranty covers only failures  
due to defects in materials or 
workmanship which occur during 
normal use. It does not cover failure 
due to damage which occurs in 
shipment, unless due to improper 

packing, or failures which result from 
accident, misuse, abuse, neglect, 
mishandling, misapplication,  
alteration, modification, or service 
by anyone other than a Heath  
warranty repair location.

Batteries and damage from battery 
leakage and all expendable items 
such as filters and tubing are ex-
cluded from this warranty.

Heath’s responsibility is expressly 
limited to repair or replacement of 
any defective part, provided the 
product is returned to an autho-
rized warranty repair location, 
shipped prepaid, and adequately 
insured. Return shipping charges 
and insurance will be paid by 
Heath warranty expense.

We do not assume liability for 
indirect or consequential damage 
or loss of any nature in connection 
with the use of any Heath product. 
There are no other warranties ex-
pressed, implied, or written except 
as listed above.

Heath warrants only that the parts 
manufactured by it will be as spec-
ified and free of defects. Heath 
makes no other warranties or rep-
resentations of any kind whatsoever, 
express or implied, and any and all 
implied warranties including any 
warranty of merchantability and 
fitness for a particular purpose or 
use are hereby disclaimed.

CAUTION: Only a qualified  
Gas Laser repair technician should 
attempt repairs/adjustments. 

CAUTION: Make no attempt to 
repair the instrument. There are no 
user serviceable components within 
the Gas Laser.

CAUTION

Содержание GAS LASER
































Отзывы: