background image

FIRE

R M LD

FIRE

R M LD

Operator’s Manual

13

GAS LASER

Doc No. 16162 Rev A, GAS LASER Operator Manual 

© 2021 Teledyne Gas Measurement Instruments Ltd. All rights reserved.

Quick & Long Press Functions 

Each button functions with either 

quick press

 and release, or a 

long press 

(hold for 1 second) and 

release. The available functions vary, 
depending upon the active screen.

quick press

 activates:

- the only function shown for a  

button, when only one function  
is available (shown below).

- the left-most or first function 

shown for a button, when two  
(2) functions are available  
(shown at right). 

A single beep will sound upon  
release to indicate a successful 
press activation. 

Turn On/Off the Instrument

Simple 3-Button Control

Navigate through screens and  
control features of the Gas Laser 
using three (3) buttons which are 
located below the screen.

Press and hold  

the middle button 

for 3 seconds to 

turn the instrument 

on/off

Button Controls

NOTICE: The                   button is a 
toggle function, and requires only  
a quick press to activate.

NOTICE: 

On all screens, the middle 

button shuts down the instrument 
when pressed and held for 3 seconds.

NOTICE

long press

 activates the right-

most or second function shown for 
a button, when two (2) functions are 
available (shown below).

A blue line under the second  
function indicates a successful  
long press activation. 

WARNING: The visible green Spotter 
laser is a Class 2 (II) laser product. 

WARNING: Do not stare 
into beam or view directly 
with optical instruments.

WARNING: Avoid direct 
eye exposure to the laser 
and do not point in the 
direction of others. Visible and 
Invisible Lasers are deployed by this 
instrument.

AVERTISSEMENT : Le Laser de 
repérage vert visible est un produit 
laser de classe 2 (II). 

AVERTISSEMENT : Ne jamais 
fixer le faisceau ni le regarder 
directement avec des instruments 
optiques.

AVERTISSEMENT : Évitez 
l’exposition directe des yeux au 
laser et ne le pointez pas vers 
d’autres personnes. Des lasers 
visibles et invisibles sont déployés 
par cet instrument.

AVERTISSEMENT

WARNING

Содержание GAS LASER
































Отзывы: