Teledyne Everywhereyoulook WAYFINDER Скачать руководство пользователя

Страница: 31 / 34

Wayfinder DVL Guide

P/N 95P-6001-00 (October 2020)

EAR-Controlled Technology Subject to Restrictions Contained on the Cover Page.

Page 27

Removing Biofouling

To remove foreign matter and biofouling

1. Remove soft-bodied marine growth or foreign matter with soapy water. Waterless hand cleaners

remove most petroleum-based fouling. Do NOT use a brush stiffer than a hand cleaning brush on

the Wayfinder urethane face.

2. Rinse with fresh water to remove soap residue.
3. Dry the Wayfinder with low-pressure compressed air or soft lint-free towels. Always dry the Way-

finder before placing it in storage to avoid fungus or mold growth. Do not store the Wayfinder in

wet or damp locations.

Protective Coating Inspection

For more protection, the Wayfinder assembly has a hard anodize coat. Do not damage the surface coatings

when handling the Wayfinder.
Inspect the Wayfinder assembly for scratches, cracks, abrasions, and exposed metal (silver-colored alumi-

num). Be critical in your judgment; the useful life of the Wayfinder depends on it. If there is any damage

to the anodizing,

DO NOT

deploy the Wayfinder. Please contact the TRDI Support Team for advice.

Содержание Everywhereyoulook WAYFINDER



































Результаты поиска

Содержание Everywhereyoulook WAYFINDER

Отзывы:

Похожие инструкции для Everywhereyoulook WAYFINDER

Бренды по названию

Популярные бренды

Teledyne Everywhereyoulook WAYFINDER, Руководство пользователя

Результаты поиска

Содержание Everywhereyoulook WAYFINDER

Отзывы:

Похожие инструкции для Everywhereyoulook WAYFINDER

Бренды по названию

Популярные бренды