Teledyne 3300TB Скачать руководство пользователя страница 50

Trace Oxygen Analyzer 

Appendix 

 

 

Teledyne Analytical Instruments  

37 

 

 

 

Section V - Emergency and First Aid Procedures 

Eye Contact: 

Flush eyes with water for at least 15 minutes 
and get immediate medical attention. 

 

Skin Contact: 

Wash affected area with plenty of water and 
remove contaminated clothing. If burning 
persists, seek medical attention. 

 

Ingestion: 

Give plenty of cold water. Do not induce 
vomiting. Seek medical attention. Do not 
administer liquids to an unconscious person. 

Inhalation: 

Liquid inhalation is unlikely. 

 

Section VI - Handling Information 

NOTE: 

The oxygen sensors are sealed, and under normal circumstances, the 
contents of the sensors do not present a health hazard. The following 
information is given as a guide in the event that a cell leaks. 

Protective clothing: 

Rubber gloves, chemical splash goggles. 

Clean-up procedures: 

Wipe down the area several times with a wet 
paper towel. Use a fresh towel each time. 

Protective measures  

during cell replacement: 

Before opening the bag containing the sensor 
cell, check the sensor cell for leakage. If the 
sensor cell leaks, do not open the bag. If there 
is liquid around the cell while in the 
instrument, put on gloves and eye protection 
before removing the cell. 

Disposal: 

Should be in accordance with all applicable 
state, local and federal regulations. 

Note:  The above information is derived from the MSDS provided 

by the manufacturer. The information is believed to be 
correct but does not purport to be all inclusive and shall be 
used only as a guide. Teledyne Analytical Instruments 
shall not be held liable for any damage resulting from 
handling or from contact with the above product. 

 

Содержание 3300TB




















































Отзывы: