Teledyne Lecroy CP030 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 24

Teledyne Lecroy CP030 Скачать руководство пользователя страница 24

CP030 Current Probe

20

922173-00 Rev A

Appendix A

Performance Verification Test Record

Photocopy this page and record the results of measurements made during the performance verification
of the CP030 Current Probe on the copy. File the completed record as required by applicable internal
quality procedures.

The sections in the test record correspond to the parameters tested in the performance verification
procedure. The numbers preceding the individual data records correspond to the steps in the procedure
that require the recording of data. Results recorded in the column labeled "Test Result" are the actual
specification limit check. The test limits are included in all of these steps. Other measurements and the
results of intermediate calculations that support the limit check are to be recorded in the column
labeled "Intermediate Results".

Permission is granted to reproduce these pages for the purpose of recording test results.

Model:

_________

________

______

Serial Number:

_________

________

______

Asset or Tracking Number:

_________

________

______

Date:

_________

________

______

Technician:

_________

________

______

Equipment Used

MODEL

SERIAL NUMBER

CALIBRATION DUE DATE

Digital Multimeter #1

Digital Multimeter #2

Function Generator

1

N/A

1

The function generator used in this Performance Verification Procedure is used for making relative

measurements. The output of the generator is measured with a DMM or oscilloscope in this procedure.
Thus, the generator is not required to be calibrated.

CP030 Test Record

Step

Description

Test Result

Gain Accuracy

10 Probe Output (Spec limit: 0.495 - 0.505 V)

________________ V

www.calcert.com

[email protected]

1.888.610.7664

0

5

10

15

20

25

30

«
...
22
23
24

Содержание CP030

























Отзывы:

Нет отзывов