manualshive.com logo in svg

Teledyne Lecroy CP030, Инструкция по эксплуатации, Страница: 16 / 24

Поделиться
Скачать
Teledyne Lecroy CP030 Скачать руководство пользователя страница 16

Instruction Manual

 

922173-00 Rev A 

11 

Adjustment Procedure 

This procedure can be used to adjust the warranted characteristics of the CP030 Current Probe. This 
procedure should be used if a parameter measured in the Performance Verification Procedure is outside 
of the specification limits. Adjustment should only be performed by qualified personnel. 

The warranted characteristics of the CP030 Current Probe are valid at any temperature within the 
Environmental Characteristics listed in the Specifications. However, some of the other test equipment 
used to verify the performance may have environmental limitations required to meet the accuracy 
needed for the procedure. Make sure that the ambient conditions meet the requirements of all the test 
instruments used in this procedure. 

NOTE

: The correct operation of the controls of the CP030 requires oscilloscope software version 4.3.0.0 

or higher. The software version in the test oscilloscope can be verified by selecting Utilities, Utilities 
Setup, then the Status tab. Contact your local Teledyne Lecroy representative if the software in your 
oscilloscope requires updating. 

Test Equipment Required   

The following table lists the test equipment and accessories, or their equivalents, which are required for 
adjustment of the CP030 Current Probe. 

Because the input and output connector types may vary on different brands and models of test 
instruments, additional adapters or cables may be required. 

Table 2. List of required equipment. 

Description   

Minimum Requirements 

Test Equipment Examples 

Wide Band Oscilloscope   

Minimum 200 MHz bandwidth 
ProBus interface equipped Software 
version 4.3.0.0 or higher 

Teledyne LeCroy WaveRunner 
6030A 

Digital Multimeter (2 required) 

DC: 0.1% Accuracy   
5½ digit resolution 

Agilent Technologies 34401A, or 
Fluke 8842A-09 

Function Generator   

50 Hz sine wave output 
3 Vrms into 50 Ω 

Agilent Technologies 33120A, or 
Stanford Research Model DS340 

Calibration Fixture, 100 Turn Loop 

100 Turn loop in series with 0.5 Ω 
±0.1% resistor with sense terminals 

Teledyne LeCroy CP030-CF02 

Banana Plug Adapter   

Female BNC to Dual Banana Plug 

Pomona 1269 

Calibration Fixture   

ProBus Extension Cable   

Teledyne LeCroy PROBUS-CF01 

www.calcert.com

[email protected]

1.888.610.7664

0

5

10

15

20

25

30

Содержание CP030

























Отзывы:

Нет отзывов