TELEDYNE API T100U Скачать руководство пользователя страница 30

Страница: 30 / 66

Troubleshooting and Service

Teledyne API - T100U Manual, Addendum to T100 Manual P/N 06807

8.3.1.2 Replacing the UV Lamp

CAUTION – GENERAL SAFETY HAZARD

Always wear safety glasses made with UV blocking material when
working with the UV Lamp assembly. (Generic plastic safety glasses are
not adequate).

1. Turn off the analyzer.

2. Disconnect the UV lamp from its power supply.

•

You can find the power supply connector by following the two, white UV Lamp
power supply wires from the lamp to the power supply.

3. Loosen, but do not remove the two UV lamp bracket screws, and the large brass

thumbscrew located on the shutter housing (see Figure 8-2) so that the lamp can be
moved.

ATTENTION

COULD DAMAGE INSTRUMENT AND VOID WARRANTY

Do not grasp the UV lamp by its cap when changing its position (see
Figure 8-2). Always grasp the main body of the lamp. Inattention to this
detail could twist and potentially disconnect the lamp’s power supply
wires.

4. Remove the UV Lamp by pulling it straight up.

5. Insert the new UV lamp into the bracket.

6. Tighten the two UV lamp bracket screws, but leave the brass thumb screw un-

tightened.

7. Connect the new UV lamp to the power supply.

8. Turn the instrument on and perform the UV adjustment procedure as defined in

section 8.3.1.1 of this addendum.

9. Finger tighten the thumbscrew.

CAUTION - GENERAL SAFETY HAZARD

DO NOT over tighten the thumbscrew, as over-tightening can cause
breakage to the lamp and consequently release mercury into the area.

10. Perform a lamp calibration procedure (see Section 4.8.7 of the T100 Manual) and a

zero point and span point calibration (see Section 9 of the T100 Manual).

06840B DCN 6201

Содержание T100U



































































Результаты поиска

Содержание T100U

Отзывы:

Похожие инструкции для T100U

Бренды по названию

Популярные бренды

TELEDYNE API T100U, Дополнение к руководству по эксплуатации

Результаты поиска

Содержание T100U

Отзывы:

Похожие инструкции для T100U

Бренды по названию

Популярные бренды