manualshive.com logo in svg

Tektronix TDS5032, Руководство пользователя

Поделиться
Скачать
Tektronix TDS5032 Скачать руководство пользователя страница 78

Tutorial 

Taking a Full Speed Signal Quality Measurement 

This section discusses how to take a Full Speed Signal Quality measurement, 
view the results, and generate a report. To perform these tasks, the application 
must be installed and enabled on a supported oscilloscope. View 

Installing the 

application

 to install the application. 

To take a Full Speed Signal Quality measurement, follow these steps: 

1. 

To set the application to default values, select File> Recall Default. The 
application displays the message ‘Default setup recalled successfully.’ 
Select OK to view a screen image showing the default settings.  

2. 

Select all the Signal Quality measurements in the Signal Quality Check area 
using Select All button. 

3. 

Select the Configure tab or select Measurements> Configure. The 
Measurements: Configure default settings display.  

4. 

Select the Measurements: Source. If the source is Live or Ref, configure the 
appropriate channels for D+, D– and Qualifier. You have to always select 
D+ first. If you select any one of the Live channels CH1-CH4 for D+ 
source, the remaining Live channels are selected from the D– and the 
Qualifier channel source. If you select any one of the Ref channels Ref1-
Ref4 for D+ source, the remaining Ref channels are selected from the D–. 
There is no Qualifier channel source for the Ref signals.  

If the source is from a file, use the browse button to look for the file.  

Select the file C:\TekApplications\tdsusb2\tsvfiles\FS_SQC.tsv. 

5. 

Select the 

 command button to run the application. The application 

displays the Eye Diagram and the Waveform Plot. 

 

64 

TDSUSB2 Universal Serial Bus Measurement Package

 

Содержание TDS5032

























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды