manualshive.com logo in svg

Tektronix TDS5032, Руководство пользователя

Поделиться
Скачать
Tektronix TDS5032 Скачать руководство пользователя страница 218

Measurement Algorithms 

 

Figure 121: Equipment setup for Low Speed Signal Quality for HUB Downstream  

Full Speed Signal Quality HUB Downstream Setup 

To set up the equipment for Full Speed Signal Quality Downstream test, follow 
these steps: 

1. 

Set the S6 switch to the Init position. 

2. 

Use the adapters to connect the A receptacle from Device SQ test section 
(marked DUT) of the test fixture to the USB2.0 Low Speed device. 

3. 

Connect Ch1 of the D+

 

probe to the D+ pins on the Device SQ section of the 

test fixture.  

4. 

Connect Ch2 of the D–

 

probe to the D– pins on the Device SQ section of the 

test fixture. 

5. 

Connect the Init port of the Device SQ section of the test fixture to any

 

port 

of the unit under test (hub) using the USB cable. 

6. 

Select the measurement and select the 

 command button to run the 

application. 

7. 

Select OK after acquiring a waveform. Verify that it is a correct waveform. 

 

204 

TDSUSB2 Universal Serial Bus Measurement Package

 

Содержание TDS5032

























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды