manualshive.com logo in svg

Tektronix TDS5032, Руководство пользователя

Поделиться
Скачать
Tektronix TDS5032 Скачать руководство пользователя страница 186

Reference 

Table 36.Error Code descriptions (cont.) 

Rising Edge Rate / Falling Edge Rate Measurement 

E901 

The High level values need to 

be decreased 

This message is displayed if no 

edge is found in the high level 

Decrease the percentage of the high level 

values of Rising Edge Rate/Falling Edge Rate 

E902  

The Low level values need to be 
increased  

If no edge is found in the low level 
the message is displayed 

Decrease the percentage of the low level 
values of Rising Edge Rate/Falling Edge Rate

E903  

Both the High and Low level 
values need to be changed  

If no edge is found in the high and 
low level the message is displayed 

Increase and decrease the percentage of the 
high and low level values of Rising Edge 

Rate/Falling Edge Rate 

E904  

The calculated Rising Edge 
Rate is more than the calculated 

bit time of the input signal  

This warning appears when the 
calculated Rising Edge Rate is 

more than the calculated bit time of 

the input signal 

Increase the lower level and decrease the 
upper level of the configure limits of Rising 

Edge Rate/Falling Edge Rate 

E905  

The calculated Falling Edge 

Rate is more than the calculated 
bit time of the input signal  

 This warning appears when the 

calculated Falling Edge Rate is 
more than the calculated bit time of 

the input signal 

Increase the lower level and decrease the 

upper level of the configure limits of Rising 
Edge Rate/Falling Edge Rate 

E906  

The calculated Rising Edge 

Rate and Falling Edge Rate is 

more than the calculated bit time
of the input signal  

This warning appears when the 

calculated Rising Edge Rate and 

Falling Edge Rate is more than the 
calculated bit time of the input 

signal 

Increase the lower level and decrease the 

upper level of the configure limits of Rising 

Edge Rate/Falling Edge Rate 

 

172 

TDSUSB2 Universal Serial Bus Measurement Package

 

Содержание TDS5032

























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды