manualshive.com logo in svg

Tektronix DG2020A, Руководство пользователя

Поделиться
Скачать
Tektronix DG2020A Скачать руководство пользователя страница 238

Appendix B: Performance Verification

DG2020A, P3410, & P3420 User Manual

BĆ27

Menu button

Bottom button

Popup menu

Side button

Front panel

button

SETUP

Level/Delay

Move the cursor to CH00 with the general purpose knob.

High Level

-, 2, ENTER

Low Level

-, 3, ENTER

3. Press the START/STOP button on the front panel so that the button’s LED

indicator lights.

4. Confirm that the reading on the digital multimeter is in the range –2.16 to

–1.84 V.

5. Set the high level voltage to 0 V, 2.0 V, 4.0 V and 7.0 V as shown in Table

B-6, and confirm that the digital multimeter reading falls within the specified
voltage ranges. Note that the low level voltage is automatically set to –2 V
when the high level voltage is set to 7 V.

Table BĆ6:  High level output voltage ranges for a 1 M

load

Settings

High level output voltage range

High level

Low level

High level output voltage range

0 V

-3.0 V

-0.10 V to 0.10 V

2.0 V

-3.0 V

1.84 V to 2.16 V

4.0 V

-3.0 V

3.78 V to 4.22 V

7.0 V

-2.0 V

6.69 V to 7.31 V

6. Move the SMB-to-BNC cable connected to the P3420 CH0 output connector

to CH1 through CH11 in turn, and confirm the high level output voltage
ranges in the same way for each of these channels.

The remaining steps confirm the low level output voltage accuracy.

7. Move the SMB-to-BNC cable connected to the P3420 data output connector

back to CH0.

8. Load the TP9DCL.PDA test pattern file from the performance check disk.

9. Press the keys shown below in the indicated order to set the low level

voltage to 6 V and the high level voltage to 7 V.

Содержание DG2020A



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды