Tektronix DG2020A Скачать руководство пользователя страница 105

Страница: 105 / 258

Reference

3Ć4

DG2020A, P3410, & P3420 User Manual

d. Define the control conditions in each line with EDIT

Make

Sequence

Repeat Count and/or the functions of EDIT

Make

Sequence

Set Enhanced Control.

Once you have created a pattern data or sequence, configure the hardware of the
DG2020A and set the output parameters.

1. Assign data bits to output channels with SETUP

Pod Assign

Assign.

2. Set the pulse high and low levels with SETUP

Level/Delay.

3. Set the output frequency with the functions of SETUP

Oscillator.

Do the following steps to output pattern data.

1. Press the START/STOP button on the front panel to start outputting.

2. Press the START/STOP button again to stop outputting.

Advanced Control for Sequence

Using the event, trigger and run mode, you can control the pattern data output
timing and sequence as your request from the external controller or just pressing
the front panel buttons. For advanced control:

1. Set the trigger wait and/or event jump into each line on the sequence with

the functions of EDIT

Make Sequence

Set Enhanced Control. See

Sequence described above.

2. Set the trigger parameters with SETUP

Trigger.

3. Set the event and/or inhibit parameters with SETUP

Pod Control.

4. Set the run mode with SETUP

Run Mode.

Setups for Output

Outputs

Содержание DG2020A



































































































































































































































































Результаты поиска

Содержание DG2020A

Отзывы:

Бренды по названию

Популярные бренды

Tektronix DG2020A, Руководство пользователя

Результаты поиска

Содержание DG2020A

Отзывы:

Бренды по названию

Популярные бренды