manualshive.com logo in svg

Tektronix CFG253, Процедуры обслуживания

Поделиться
Скачать
Tektronix CFG253 Скачать руководство пользователя страница 18

CFG253

Performance Verification & Adjustment Procedures

Page 18 of 19

Procedure #: CP1005   Revision: A

d.

Set the RANGE to 1M and adjust C8 for a reading of 3.0 MHz on the Frequency

Counter.

e.

Check the Frequency Counter readout while changing the CFG253 FUNCTION

between Sine Wave and Square Wave.  Adjust R76 for approximately 3.0 MHz,

setting for the best compromise between Sine Wave and Square Wave.

*** Alternate Procedure ***

( If a Frequency Counter is not available )

f.

Set-Up:

AMPLITUDE

CW

RANGE

1K

FUNCTION

Triangle

VOLTS OUT

Button Out

FREQ/10

Button Out

FREQ DIAL

3.0

g.

Test Scope Set-Up:

Volts/Div

0.5 V

Time/Div

0.2 mSec

h.

Connect SYNC/TTL OUTPUT to test scope vertical input via coax cable and 50
ohm terminator.

i.

Adjust R6 for a display of 6 cycles in 10 Divisions on the test scope.  (3KHz)

j.

Set RANGE to 1M and the test scope Time/Div to 0.2 uSec.

k.

Adjust C8 for a display of 6 cycles in 10 Divisions on the test scope.  (3MHz)

l.

Check display while changing the FUNCTION between Sine Wave and Square
Wave.  Adjust R76 for 6 cycles in 10 Divisions, setting for the best compromise
between Sine Wave and Square Wave frequencies.

Содержание CFG253




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды