manualshive.com logo in svg

Tektronix CFG253, Процедуры обслуживания

Поделиться
Скачать
Tektronix CFG253 Скачать руководство пользователя страница 14

CFG253

Performance Verification & Adjustment Procedures

Page 14 of 19

Procedure #: CP1005   Revision: A

4.

Set DC Offset

a.

Set-Up:

DC OFFSET

Pulled Out

RANGE

1K

FUNCTION

All Buttons Out

VOLTS OUT

Button Out

FREQ/10

Button Out

b.

Test Scope Set-Up:

Volts/Div

2V

Time/Div

0.2 mSec

Var Time/Div

Cal

c.

Connect MAIN OUTPUT to test scope vertical input via coax cable and 50 ohm
terminator.

d.

Set test scope Vert Coupling to GROUND, center the trace, then set Coupling
back to DC.

e.

While turning the DC OFFSET knob from CCW to CW and back, adjust R117 for
equal voltage swings positive and negative on the test scope.

f.

Adjust R129 for 5.1 V with DC OFFSET knob CW and -5.1 V with the knob CCW
(2.55 Div on test scope).  Repeat step e, if necessary.

g.

Push the DC OFFSET knob in (off).

h.

Set the test scope to 10 mV/Div.

i.

Set test scope Vert Coupling to GROUND, center the trace, then set Coupling
back to DC.

j.

Slowly adjust R82 to recenter the trace, set to within 1 division of center (+/- 10
mV).

Содержание CFG253




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды