manualshive.com logo in svg

Tektronix CFG253, Процедуры обслуживания

Поделиться
Скачать
Tektronix CFG253 Скачать руководство пользователя страница 12

CFG253

Performance Verification & Adjustment Procedures

Page 12 of 19

Procedure #: CP1005   Revision: A

Test Equipment requirements

The test equipment listed in the Table on Page 2 is a list of the equipment needed for
this performance check.  All test equipment is assumed to be operating within
tolerance.  Detailed operating instructions for test equipment are not given in this

procedure.  If operating information is needed,  refer to the appropriate test equipment

instruction manual.

Initial CFG253 Set-Up:

AMPLITUDE

CCW

DC OFFSET

Pushed In

SYMMETRY

Midrange Detent

RANGE

1K

FUNCTION

All Buttons Out

VOLTS OUT

Button Out

FREQ/10

Button Out

SWEEP

Button Out

SWEEP RATE

Midrange

SWEEP WIDTH

Midrange

FREQ DIAL

0.3

1.

Set U1 Input Voltage

a.

Set digital multimeter to DC mV range

b.

Connect multimeter test leads to pins 2 and 3 of Integrated Circuit U1.

Note: Alternate Test Points

Locate R8 and R9 at the front left edge of the Main circuit board.
Pin 2 is connected to the end of R8 nearest the board edge.  Pin 3 is
connected to the end of R9 furthest from the board edge.

c.

Adjust R10 for approximately 0 mV.

2.

Set Q5 Gate Voltage

a.

Connect common lead of multimeter to ground and the positive lead to the wire
loop test point near gate of Q5.  (on the Main board under rear edge of the
elevated Switch board).

b.

Adjust R33 for approximately 0 mV.

Содержание CFG253




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды