Tekmar Mixing Control 361 Скачать руководство пользователя страница 17

Copyright © D 361 - 

03/09

17 of 20

Testing the Control

The Mixing Control 361 has a built-in test routine which is used to test the
main control functions. The 361 continually monitors the sensors, and
displays an error message whenever a fault is found. See the following
pages for a list of the 361’s error messages and possible causes. When
the 

Test

 

button is pressed, the test light is turned on. The individual

outputs and relays are tested in the following test sequence.

TEST SEQUENCE 

Each step in the test sequence lasts 10 seconds.

During the test routine, the test sequence may be paused by pressing the 

Test

 button. Only if there is a mixing demand can the control

be paused in a step. If the 

Test

 button is not pressed again for 5 minutes while the test sequence is paused, the control exits the entire

test routine. If the test sequence is paused, the 

Test

 button can be pressed again to advance to the next step. This can also be used

to rapidly advance through the test sequence. To reach the desired step, repeatedly press and release the 

Test

 button until the

appropriate device and segment in the display turn on.

Step 1

- The injection pump operates at 100% for 10 seconds. After 10 seconds, the injection pump is shut off.

Step 2

- The system pump (

Sys Pmp) is turned on for 10 seconds.

Step 3

- The 

Boiler contact is turned on for 10 seconds. After 10 seconds, the Boiler and Sys Pmp contacts are shut off.

Step 4

- After the test sequence is completed,  the control resumes its normal operation.

Adjust 

Menu

 

(2 of 2)

The system’s warm weather shut down during the
occupied (Day) period.

35 to 100

°

F, OFF

(2 to 38

°

C, OFF)

B3

Section

Advanced

Installer

Display

Description

Range

Actual

Setting

The system’s warm weather shut down during the
unoccupied (Night) period.

35 to 100

°

F, OFF

(2 to 38

°

C, OFF)

 B3

The units of measure that all of the temperatures
are to be displayed in the control.

°

F, 

°

C

This item exits the ADJUST menu by pressing
either the   or   button.

Test

not testing

testing

testing paused

off

red

red

ADJUST

WWSD

°

F

OCC

ADJUST

WWSD

°

F

OCC

UN

ADJUST

°

F

ADJUST

Содержание Mixing Control 361





















Отзывы: