Tekmar D 270 Скачать руководство пользователя страница 5

 

5 of 24 

 © 2010          D 270 - 08/10

EXERCISING

The control has a built-in exercising feature that is selected through the 

Exercise / Off DIP

 switch. To enable the exercising feature 

set the 

Exercise / Off

 DIP switch to 

Exercise

. If exercising is enabled, the control ensures that each pump is operated at least 

once every 3 days. If a pump has not been operated at least once every 3 days, the control turns on the output for 10 seconds. 
This minimizes the possibility of the pump seizing during a long period of inactivity. While the control is exercising, the 

Test

 LED 

flashes quickly.

Note:

 The exercising function does not work if power to the control or pumps is disconnected.

RUNNING TIMES

The control displays the accumulated running time of the boiler in the VIEW menu.

Resetting the Running Time

To reset the running time for the boiler, select the running time in the VIEW menu. Next press the   and   buttons simultaneously 
until 

CLR

 is displayed.

FACTORY DEFAULTS

The control comes preset with several factory defaults. These are based on the terminal unit selection. To fine-tune building 
requirements, these defaults may be changed.

To reload the factory default, power down the control and wait for 10 seconds. Power up the control while simultaneously 
holding the 

Menu

 and   buttons. An E01 error occurs forcing the installer to go through the ADJUST menu to ensure the 

settings are correct.

BOILER MINIMUM

The boiler minimum is the lowest temperature that the control is 
allowed to use as a boiler target temperature. During mild conditions, 
if the control calculates a boiler target temperature that is below the 

Boiler Minimum 

setting, the boiler target temperature is adjusted to at 

least the 

Boiler Minimum

 setting. During this condition, if the boiler is 

operating, the minimum segment is turned on in the display when viewing 
either the boiler supply temperature or the boiler target temperature. Set 
the 

Boiler Minimum 

setting to the boiler manufacturer’s recommended 

temperature.

BOILER MAXIMUM

The boiler maximum is the highest temperature that the control is 
allowed to use as a boiler target temperature. If the control does target 
the 

Boiler Maximum 

setting, and the boiler temperature is near the boiler 

maximum temperature, the maximum segment will be displayed in the 
LCD while either the boiler target temperature or the boiler temperature 
is being viewed. At no time does the control operate the boiler above 
248

°

F (120

°

C).

FIRE DELAY

The Fire Delay is the time delay that occurs between the time that the control 
closes a stage contact to fire a stage and the burner fires for that stage.

MIN Segment On

MAX Segment

On

MAX Segment

On

Boiler

Contact Closes

Boiler

Fires

Fire

Delay

Time

BOILER TARGET TEMPERATURE

The boiler target temperature is determined by the type of demand received by the control. A boiler demand calculates a boiler 
target based on the characterized heating curve settings and the outdoor air temperature. A DHW demand has a temperature 
setting to which the boiler is operated to meet. 

The control displays the temperature that it is currently trying to maintain as the boiler supply temperature. If the control does not 
presently have a requirement for heat, it does not show a boiler target temperature. Instead, “– – –” is displayed in the LCD.

Section B: Boiler Operation

Содержание D 270

























Отзывы: