Tecumseh OHH50 - 65 Скачать руководство пользователя страница 85

Страница: 85 / 94

REMOVE

BOLTS

SLIDE TANK

22. Attach the fuel tank (if applicable) using bolts

or wedging the tank in the blower housing slots

provided. Attach the fuel line and secure with

clamps.

23. Slide the fuel line on the carburetor fitting and

secure with a clamp. Slide the breather tube

on the carburetor or air cleaner fitting if

applicable.

NOTE:

If the tank is supplied by the O.E.M.

replace the fuel filter. Tecumseh's tanks have

a fuel filter in the tank and service is not

necessary.

24. Fill the engine with oil to the full mark on the

dipstick. Add fresh fuel to the fuel tank and

secure the cap.

25. Install the spark plug and high tension lead.

Mount the engine to the equipment and

connect wiring and control cables. OVRM

rotary mower engines require the blade to be

secured to the blade hub adapter and

crankshaft before attempting to start the

engine.

26. Start the engine and allow it to run

approximately five minutes to reach operating

temperature. Optimize the carburetor if

adjustable, verify top no load and idle RPM

settings.

Содержание OHH50 - 65































































































Результаты поиска

Содержание OHH50 - 65

Отзывы:

Похожие инструкции для OHH50 - 65

Бренды по названию

Популярные бренды

Tecumseh OHH50 - 65, Руководство пользователя

Результаты поиска

Содержание OHH50 - 65

Отзывы:

Похожие инструкции для OHH50 - 65

Бренды по названию

Популярные бренды