Tecumseh OHH50 - 65 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 94

background image

79

12.

STEPS 12A -12G APPLY ONLY TO EARLY

PRODUCTION ENGINE MODELS OHM,

OHSK120, OVM AND OVXL.

CONTINUE

WITH STEP 13 FOR CURRENT

PRODUCTION MODELS.

a. Install the push rods with the cupped ends

of the rods placed on top of the lifters.

Visually check correct placement through

the valve box opening. Use lubricated new

"O" ring seals for both ends of the push

rod tubes and install the push rod tubes in

the crankcase.

b. Install the valves into the head, and using a

new head gasket, place the head on the
cylinder block. Tighten the head bolts in the
numbered sequence using 60 inch pound
(6.8 Nm) increments to the specified torque.

c. Install the rocker arm housing, push rod

guide plate with the legs facing up, new
rocker arm studs with "O" rings under the
guide plate. Install the valve box to head
retaining screw using a flat washer and a
new "O" ring. Tighten the screw and the
studs to the specified torque.

d. Lift each valve up until it contacts the seat

and hold the valve in this position. Use a 12
inch (30.5 cm) piece of fuel line and wedge
one end on each side of the valve stem
through the port opening to hold the valve.

e. Bolt the valve spring compressor tool part

# 670315A on a rocker arm stud using the
rocker arm bearing and locking nut (diag.
66).

f. Install the new o-rings (white o-ring on the

exhaust guide) followed by valve spring
caps, valve springs with the dampening coils
toward the head, (diag. 64) and valve spring
retainers with the larger opening away from
the engine.

g. Compress the valve spring with the tool and

insert the two retainers into the keeper so

the inside ridge of the retainer locks into

the valve stem groove. Repeat the

procedure for the other valve (diag. 66).

NOTE: TORQUE THE CYLINDER HEAD

FOLLOWING THE SEQUENCE ON

PAGE 69.

DAMPENING COILS

LOCATED CLOSER

TOGETHER

THIS END MUST FACE

TOWARD THE

STATIONARY PART

OF THE ENGINE

(CYLINDER HEAD)

"O" RINGS

TEFLON EXHAUST
(WHITE)

(BLACK)

RETAINERS HELD BY SPRING
TENSION AGAINST THE CAP

VALVE SPRING
COMPRESSOR TOOL
PART NO. 670315

CAP

RETAINER

OVM / OHM STYLE

64

66

OVRM/OHH 1.105 (28.067 mm)

FREE LENGTH

1.980" (50.292 mm)

ALL OTHERS

65

«
...
80
81
82
83
84
...
»

Содержание OHH50 - 65































































































Отзывы:

Нет отзывов

Похожие инструкции для OHH50 - 65

Бренд: Westerbeke Страницы: 112

MULTI-VANE 1800 Series

Бренд: Ingersoll-Rand Страницы: 12

Бренд: Schartec Страницы: 16

Бренд: Saito Страницы: 2

Бренд: Saito Страницы: 2

Бренд: Saito Страницы: 7

Бренд: Hatz Страницы: 94

Бренд: Volvo Penta Страницы: 100

Бренд: Volvo Penta Страницы: 104

Бренд: YS Страницы: 5

Бренд: Gude Страницы: 52

Бренд: aFe Power Страницы: 16

Бренд: Winterthur Gas Страницы: 495

Бренд: Robin America Страницы: 32

Бренд: Robin America Страницы: 35

Бренд: Baotian Страницы: 41

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды