background image

1

CHAPTER 1 GENERAL INFORMATION

ENGINE IDENTIFICATION

Tecumseh engine model, specification, and serial

numbers or date of manufacture (D.O.M.) are stamped

into the blower housing, or located on a decal on the

engine in locations as illustrated (diag. 1 & 2). The

engine identification decal also provides the applicable

warranty code and oil recommendations (diag. 2).

Interpretation of Model Number

The letter designations in a model number indicate

the basic type of engine.
OHH  - Overhead Valve Horizontal
OHM  - Overhead Valve Horizontal

MediumFrame

OHSK  - Overhead Valve Horizontal Snow King
OVM  - Overhead Valve Vertical Medium Frame
OVRM  - Overhead Valve Vertical Rotary Mower
OVXL  - Overhead Valve Vertical Medium Frame

Extra Life

OHV  - Overhead Valve Vertical
The number designations following the letters indicate

the basic engine model.
The number following the model number is the

specification number. The last three numbers of the

specification number indicate a variation to the basic

engine specification.
The serial number or D.O.M. indicates the production

date of the engine.
Using model 

OHV16-204207A

, serial 

5215C

 as an

example, interpretation is as follows:

OHV16-204207A

 is the model and specification

number.

OHV

Overhead Valve Vertical

16

Indicates the basic engine model.

204207A

is the specification number used for

properly identifying the parts of the

engine.

5215C

is the serial number or D.O.M. (Date of

Manufacture)

5

is the last digit in the year of

manufacture (1995).

215

indicates the calendar day of that year

(215th day or August 3, 1995).

C

represents the line and shift on which

the engine was built at the factory.

Emissionized engines that meet the California Air

Resource Board (C.A.R.B.) or the Environmental

Protection Agency (E.P.A.) standards will include

additional required engine information on the engine

decal.

NOTE:

 To maintain best possible emission

performance, use only Genuine Tecumseh Parts.

1

2

ENGINE MODEL

NUMBER

THIS ENGINE MEETS 1995-1998

CALIF. EMISSION REGULATIONS FOR

ULGE ENGINES AS APPLICABLE

FUEL: REGULAR UNLEADED OIL : USE SAE 30

OHV 125 203000A        (D)

RTP358UIG2RA

358cc

3057D

Содержание OHH50 - 65































































































Отзывы: