TechnipFMC Smith Meter AccuLoad IV Скачать руководство пользователя страница 66

Страница: 66 / 72

AccuLoad IV Installation & Maintenance Manual

Maintenance

6 Maintenance

The following sections provide information about maintaining your AccuLoad IV to ensure optimal

functionality.

6.1 Explosion-Proof Enclosure Maintenance

AccuLoad ST and QT models with explosion-proof enclosures (with XP in the model code) should be

maintained using the following flame-path inspection criteria.

•

Installation, inspections, maintenance. repairs, overhauls, and reclamation of AccuLoads in the

European Union (EU) must be performed by qualified personnel in accordance with the applicable

requirements of EN 60079-14, EN 60079-17, and EN 60079-19, in addition to all local codes and

regulations.

•

Installation, inspections, maintenance, repairs, overhauls, and reclamation of AccuLoads relying on

IECEx certification must be performed by qualified personnel in accordance with the applicable

requirements of IEC 60079-14, IEC 60079-17, and IEC 60079-19, as required by local codes and

regulations.

•

Guidance for equipment inspection and maintenance is provided by EN/IEC 60079-17: Electrical Apparatus

for Explosive Gas Atmospheres, Inspection and Maintenance of Electrical Installations in Hazardous

Areas, and should be used for the inspection and maintenance process.

•

When performing maintenance that requires opening the enclosure cover, all flame paths (defined as

the machined-flanged surface between the housing and the cover), should be inspected to ensure that

they are clean, undamaged, and have no scratches, nicks, corrosion, or other defects that could affect

the integrity of the flame path. If defects are detected, the equipment should not be placed back into

service until the issues are resolved.

•

Verify that all tapped cover bolt threaded locations in the enclosure are clean and intact with no missing

or stripped threads.

•

Verify that the cover bolts are the required M8 x 1.25-6g, DIN 912, steel grade 12.9. Prior to

reassembly, apply a light coating of nickel-based anti-seize lubricant, such as Loctite Anti-Seize

Lubricant (TechnipFMC part number 646002-401) to all bolt threads.

•

Verify that any blind-threaded cover bolt holes do not have excessive grease or anti-seize lubricant

packed into them, as this could cause hydraulic fractures of the enclosure when the bolts are tightened.

•

Inspect to ensure that the environmental O-ring is correctly installed (seated into the groove) and in

good condition (no cracks, etc.). If the O-ring is defective, replace it to maintain environmental

protection. Grease the cover flange with petroleum jelly or Super Lube Multi-Purpose Synthetic Grease

with Syncolon (TechnipFMC part number 644886-401) before reattaching the cover to the housing.

•

Follow the cover bolt torquing procedure as outlined in

Section 5.1: Closing the Explosion-Proof

Housing

. When complete, verify the flame path gaps according to the procedure.

WARNING:

To prevent the ignition of hazardous atmospheres, disconnect the AccuLoad from its main

power supply before opening the cover.

Содержание Smith Meter AccuLoad IV









































































Результаты поиска

Содержание Smith Meter AccuLoad IV

Отзывы:

Бренды по названию

Популярные бренды

TechnipFMC Smith Meter AccuLoad IV, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Smith Meter AccuLoad IV

Отзывы:

Бренды по названию

Популярные бренды