Technibel Climatisation CAFM страница 81 Скачать руководство пользователя

Страница: 81 / 130

6-6. Wiring the Remote Controller

Connection diagram

Use 0.5 mm

– 2 mm

wires.

(1) Strip the insulation to approximately 14 mm from

the ends of the wires that will be connected.

(2) Twist together the 2 wires and create a crimp con-

nection at the wire joint.

(3) If a special crimping tool is not used, or if the con-

nection is soldered, insulate the wires using insu-

lation tape.

Use the remote controller cord (optional) for remote
controller wiring.

(1) Disconnect the lead wire that is wound around the

lead wire anchor on the remote controller unit. Dis-

connect the connector and connect the remote

controller cord (optional) to the connector on the

remote controller unit. Insert the remote controller

cord (optional) into the groove and bend it into the

correct shape, then wind it around the lead wire

anchor.

(2) If the remote controller cord (optional) is used,

refer to the installation manual that is provided

with the cord.

Terminal board for
indoor unit remote
controller wiring

1
2

Remote controller wiring
(field supply)

Connector

Remote
controller
unit

Power wire from remote
controller unit

Approx.
200 mm

Remote controller wiring

Power wire from
remote controller
unit

Provided wire joint
(white)

Wire joint
CE-1, white

Remote controller cord (optional)

Connector

Lead wire anchor

06-062 Mini ECO-i II for Technibel 2/8/06 4:32 PM Page 81

Содержание CAFM



































































































































Результаты поиска

Содержание CAFM

Отзывы:

Похожие инструкции для CAFM

Бренды по названию

Популярные бренды

Technibel Climatisation CAFM, Руководство по установке

Результаты поиска

Содержание CAFM

Отзывы:

Похожие инструкции для CAFM

Бренды по названию

Популярные бренды