Technibel Climatisation CAFM страница 48 Скачать руководство пользователя

Страница: 48 / 130

MAFM

Fig. 3-66

3-20. Installing the Rear Panel onto the Wall

Confirm that the wall is strong enough to support the unit.

See either Item a) or b) below depending on the wall

type.

a) If the Wall is Wooden

(1) Attach the rear panel to the wall with the 10 screws

provided. (Fig. 3-66)

If you are not able to line up the holes in the rear panel

with the beam locations marked on the wall, use Rawl

plugs or toggle bolts to go through the holes on the

panel or drill 5 mm dia. holes in the panel over the

stud locations and then mount the rear panel.

(2) Check with a tape measure or carpenter’s level. This

is important so that the unit is correctly installed.

(Fig. 3-67)

(3) Make sure the panel is flush against the wall. Any

space between the wall and unit will cause noise

and vibration.

b) If the Wall is Brick, Concrete or Similar

Drill 4.8 mm dia. holes in the wall. Insert Rawl plugs for

appropriate mounting screws. (Fig. 3-68)

3-21. Removing the Grille to Install the Indoor Unit

In principle, with this model wiring can be completed

without removing the grille.

However, if it is necessary to change the settings on the

PCB, follow the procedure below.

Removing the grille

(1) Lift up on both sides of the air-intake grille to open it.

(Fig. 3-69)

(2) Remove the filter. (Fig. 3-69)

(3) Adjust the flap so that it is horizontal. (Fig. 3-70)

(4) Open the installation screw covers below the grille

(3 locations). (Fig. 3-70)

(5) Remove the screws. (Fig. 3-70)

(6) Remove the grille. (Fig. 3-71)

Attaching the grille

(1) Close the flap.

(2) Keep the grille installation tabs aligned with the top

portion of the grille, and reinstall the lower portion of

the grille.

Fit the installation tabs into the grooves and press

the lower portion of the grille back into its original

position to install it.

(3) Press on the installation tabs to completely close

the grille.

Check that the grille and frame are fitted tightly

together.

Fig. 3-67

Fig. 3-68

Fig. 3-69

Fig. 3-70

Fig. 3-71

4.8 mm
dia. hole

Rawl plug

Intake grille

Filter

Flap

Open the grille

Installation screw cover

Remove the grille

06-062 Mini ECO-i II for Technibel 2/8/06 4:32 PM Page 48

Содержание CAFM



































































































































Результаты поиска

Содержание CAFM

Отзывы:

Похожие инструкции для CAFM

Бренды по названию

Популярные бренды

Technibel Climatisation CAFM, Руководство по установке

Результаты поиска

Содержание CAFM

Отзывы:

Похожие инструкции для CAFM

Бренды по названию

Популярные бренды