Technibel Climatisation CAFM Скачать руководство пользователя страница 117

Страница: 117 / 130

CAFM1VS

CAFM2V

117

K70D038Z for 2-Way and High Ceiling

1-Way Type (CAFM2V, CAFM1VS Type)

For 2-way Cassette Type (CAFM2V Type)

11-11. Installing the Display

Remove panel cover A and install the display.

(1) Remove cover A from the rear side of the panel.

(2) Cover B is fit inside cover A. Therefore, spread

cover A and remove cover B, as shown in Fig. 11-

13.

Remove the tape that holds cover B in place. It

was used for protection during shipping.

(3) Fit the display into the panel.

(4) Pass the display lead wire through the notch in the

panel. Use the hole in the plate and a clamp to

fasten the wire in place.

(5) Reattach cover A.

11-12. Installing the Control Unit

Do not twist the control wiring with the power wiring
because this may cause malfunction.

Install a noise filter or take other appropriate action
if electrical noise affects the power supply circuit of
the unit.

(1) Use the 2 supplied screws (4

10) to attach the

control unit at the location shown in the diagram

below.

(2) Connect the display and control unit 6P connec-

tors.

(3) Connect the control unit lead wire to the indoor

unit remote controller wiring terminal.

(4) Bend the lead wire into the correct shape, and use

a figure 8 clamp to fasten it in place.

(5) Attach the ceiling panel.

* For the wiring and test run procedures, refer to

“Wiring the Receiver Unit” and “Test Run.”

NOTE

Spread

Cover B

Display

Cover A

Fig. 11-13

Fasten wire in hole of plate.

Pass display lead
wire through notch
in panel.

Fig. 11-14

Bend excess lead wire,
then use figure 8 clamp to fasten it in place.

Control unit

Fig. 11-15

06-062 Mini ECO-i II for Technibel 2/8/06 4:32 PM Page 117

Содержание CAFM



































































































































Результаты поиска

Содержание CAFM

Отзывы:

Technibel Climatisation CAFM, Руководство по установке, Страница: 117 / 130

Результаты поиска

Содержание CAFM

Отзывы: