background image

 

Page 8 

The  door  monitoring  contact  (IN1)  is  operational  after  its  first  change  of  status  since 
switching on the module. Full door lock timing acc. to 

tab. 10

 is used when the door status 

contact is not installed and no Forced Door and Door Ajar alarms are triggered. 

4.4  Installation instructions 

The reader module uses passive RF/ID technology, which is sensitive to RF noise sources. 
Noise sources are generally of two types: radiating or conducting. 

Conducted noise enters the reader via wires from the power supply or the host. Sometimes, 
switching  power  supplies  generate  enough  noise  to  cause  reader  malfunction,  it  is 
recommended to use linear system power supplies. 

Radiated noise is transmitted through the air. It can be caused by computer monitors or other 
electrical equipment generating electromagnetic fields. 

Consequently, a short distance between the reader modules themselves can cause reading 
malfunctions 

– for correct operation it is necessary to keep a minimum distance of 50 cm. 

Various metallic constructions may have a negative influence on this distance; if there are 
any doubts, it is recommended to make a practical test before final mounting.  

Nearby metal surfaces may cause a decrease in reading distance and speed. This is caused 
by the combined effects of parasitic capacitance and conductance. 

 

 

Содержание APS mini MREP 78 Series

























Отзывы: