background image

 

Thank you for choosing a product from Tecfluid S.A.  

This instruction manual allows the installation, configuration, 
programming and maintenance. It is recommended to read it before 
using the equipment. 

• 

This document shall not be copied or disclosed in whole or in any 
part by any means, without the written permission of Tecfluid S.A. 

• 

Tecfluid S.A. reserve the right to make changes as deemed 
necessary at any time and without notice, in order to improve the 
quality and safety, with no obligation to update this manual. 

• 

Make sure this manual goes to the end user. 

• 

Keep this manual in a place where you can find it when you need 
it. 

• 

In case of loss, ask for a new manual or download it directly from 
our website 

www.tecfluid.com

  Downloads section. 

• 

Any deviation from the procedures described in this instruction 
manual, may cause user safety risks, damage of the unit or cause 
errors in the equipment performance. 

• 

Do not modify the equipment without permission. Tecfluid S.A. are 
not responsible for any problems caused by a change not 
allowed. If you need to modify the equipment for any reason, 
please contact us in advance. 

PREFACE 

WARNINGS 

Содержание CIP II















Отзывы: