background image

14 

 

WARRANTY 

Tecfluid S.A. guarantee all the products for a period of 24 months from their sale, against all faulty 
materials, manufacturing or performance. This warranty does not cover failures which might be 
imputed to misuse, use in an application different to that specified in the order, the result of service or 
modification carried out by personnel not authorized by Tecfluid S.A., wrong handling or accident. 

This warranty is limited to cover the replacement or repair of the defective parts which have not 
damaged due to misuse, being excluded all responsibility due to any other damage or the effects of 
wear caused by the normal use of the devices. 

Any consignment of devices for repair must observe a procedure which can be consulted in the 
website www.tecfluid.com, “After-Sales” section. 

All materials sent to our factory must be correctly packaged, clean and completely exempt of any 
liquid, grease or toxic substances. 

The devices sent for repair must enclose the corresponding form, which can be filled in via website 
from the same “After-Sales” section. 

Warranty for repaired or replaced components applies 6 months from repair or replacement date. 
Anyway, the warranty period will last at least until the initial supply warranty period is over. 

TRANSPORTATION 

All consignments from the Buyer to the Seller´s installations for their credit, repair or replacement must 
always be done at freight cost paid unless previous agreement. 

The Seller will not accept any responsibility for possible damages caused on the devices during 
transportation. 

Tecfluid S.A. 

Narcís Monturiol 33 

08960 Sant Just Desvern 

Barcelona 

Tel:   +34 93 372 45 11 

Fax:  +34 93 473 44 49 

tecfluid@tecfluid.com 

www.tecfluid.com 

The technical data described in this manual is subject to modification without notification if the technical innovations in the 

manufacturing processes so require. 

Quality Management System ISO 9001 certified by 

 

Pressure Equipment Directive certified by 

 

ATEX European Directive certified by 

 

 

Содержание CIP II















Отзывы: