4
TEC-61231-23 Technical Manualе
PRIZRAK
Alarm operation algorithms
Arming/disarming
To arm the alarm press the lock button of the remote, or close the
doors with keyless system or lock the door with the key. Alarm will
warn you that it is armed with audible signal and LED flashes. After
some time interval between flashes will decrease.
To disarm the alarm press unlock button of the remote, or open
vehicle with keyless system. Alarm will warn you with 2 audible signals.
LED will go off.
Arming and disarming can be done by the voice menu or the
mobile application
Warning about open door
If you left an open door, hood or trunk and armed the Alarm, the
system will warn you with 3 audible signals. LED will inform you about
open compartment:
•
Two – the hood is open
•
Three – the trunk is open
•
Four – the door is open.
The Alarm cannot monitor entry through unlocked door. It is
possible to close the doors (hood, trunk) while still in Security
mode, then the Alarm will automatically continue monitoring
Triggering the Alarm
The alarm has 2 built-in sensors: shock sensor and tilt/movement
sensor. Because of these sensors the alarm is able to differentiate
different influences on the vehicle. Optional sensor can be connected
if required. The alarm can be connected to multiplex sensors and
standard sensors.
In secure state alarm can react to external action by warning or
by triggering. Warning will be made if small force was applied to the
shock sensor. In this case alarm will make short audio signals.
Alarm will be triggered, if any door, hood, or trunk is open, if tilt/
movement sensor is triggered, and if excessive force was applied to
the shock sensor. Siren will be on for 30 seconds and hazard lights
will blink.
You can adjust sensors sensitivity.
Function of protecting public order
After three triggers in armed mode from one sensor in one hour
alarm will stop responding to this sensor for one hour. Alarm will
continue working with this sensor if there were no triggers for one
hour. This function will cancel alerts but warnings will stay
Trigger check
Alarm remembers causes of alerts for security period. Memory will
be cleared after ignition switched on.
If alarm was triggered, after disarming the alarm four audible
signals will be made and indcation of cause will start (check table 1).
Table 1.
Trigger indication
LED flashes
Note
x1
Public order feature
x2
Hood was opened
x3
Trunk was opened
x4
Door(s) was (were) opened
x5
Triggering of the shock sensor (alarm)
x6
Triggering of the shock sensor (warning)
x7
Triggering of the tilt/displacement sensor
x8
Triggering of an extra sensor (alarm)
x9
Triggering of an extra sensor (warning)
Detailed
information
about
events
can be found in the trigger log which can be accessed from the voice menu.
Arming with sensor deactivation
There are situations when you need to arm the Alarm with sensor
input deactivation.
To deactivate sensors:
•
Arm the alarm
•
Press the remote control button for 3 seconds. The siren will
emit one long intermittent sound, then a short sound after a
pause. Now the warning is off. The Alarm will not respond to
mild impact to the vehicle
•
Within the next 3 seconds press the remote control button
again: the siren will emit one long intermittent sound, then two
more signals after a pause. Now all sensors are deactivated.
Trunk opening without leaving the security mode
You can open the trunk with remote or keyless system. While
trunkis open alarm will stop reacting to sensor input, but will control
doors so the vehicle will stay secured from intrusion. After trunk is
closed, the system will secure it and turn all sensors back on.
Hands-free function
When the engine was started remotely, hands-free function
will check that the RFID tag is within the coverage. The Alarm will
automatically unlock the vehicle upon owners approach, and will lock
it back when owner left the vehicle.
RFID check when disarming
In this mode when you unlock the vehicle via remote control or
keyless access system, the Alarm will search for the RFID tag. Only
after the RFID tag is detected, the vehicle will be disarmed.
The RFID tag is looked for only if the Alarm was armed for
more than 30 seconds. While searching the system will emit
intermittent sound. If you don’t have the RFID tag with you,
then within 10 seconds after a door, hood or trunk is opened,
an alarm will go off. To deactivate the alarm signal, turn on the
ignition and authenticate yourself.
Factory remote door lock control
This function does not allow opening doors by using signal imitation
equipment, and also will lock access into vehicle in case if the remote
was stolen (if electromechanical locks were installed).
After receiving a signal to open from the factory remote, the alarm
will search for RFID tag, and only after authentication, doors will open.
Feature can operate permanently – RFID tag will be required every
disarming of the alarm, and temporary in places where you need
maximum safety(see. Quick engaging of the second circuit for higher
risk locations). Toggling and selection of the operational mode is done
in the alarm hardware features menu.
There are three methods to use this feature. Each method can be used on its own or together with other methods:
