background image

B

B

B

B

BA

A

A

A

AG D (Contin

G D (Contin

G D (Contin

G D (Contin

G D (Continued)

ued)

ued)

ued)

ued)

14

Figure 32

Step D-7

Diff Adjusting Screw Assembly:

83

84

‰

1. Very carefully insert the Diff Thrust Assembly, into the female

Outdrive  (83). Be very careful to make sure the Thrust Balls (88)
remain seated between the Thrust Washers (86) while inserting the
Diff  Screw. Pull the threaded end of the Diff Screw until the Thrust
Bearing assembly rests against the inside of the female Outdrive.

 IMPORTANT NOTE:

 Ensure that all eight Thrust Bearing

Balls remain in place between the two Washers, around the Diff Screw.

Step D-6

Figure 31

Bearing Insert to Female Outdrive:

*NOTE: Be very careful when installing the foam Thrust Bear-

ing Seals, do not over-stretch them.

‰

1. Locate the Diff Adjusting Screw (84) and carefully stretch the

two blue foam Thrust Bearing Seals (85) into the groves on the head
of the Diff Screw.

‰

2. Place one of the Belleville Washers(75) onto the Diff Adjust-

ing Screw with the cone pointing toward the head of the Diff Screw.

          *NOTE: The Thrust Bearing Washers are packaged in a small
bag along with the eight 5/64" Thrust Bearing Balls.

‰

3. Place a Thrust Washer (86) on the Diff Screw against the

Belleville Washer.

‰

4. Grease the Thrust Washer well with White Thrust Bearing/

Assembly Grease (87) and place the eight 5/64" Thrust Bearing Balls
(88) on top of the Thrust Washer, around the Diff  Screw. Apply more
White Thrust Bearing/Assembly Grease to the top of the Thrust Bear-
ing Balls.

‰

5. Place another Thrust Bearing Washer over the Diff  Screw and

against the Thrust Bearing Balls.

‰

6. Place another Belleville Washer on the Diff Screw with the

cone opening towards the head of the Thrust Washer.

85

75

88

86

84

85

88

75

86

GREASE

84

Содержание XXX-T MF2













































Отзывы: