background image

 

 

409-35036 

Rev A 

of 15

 

SUPPORT CENTER 

CALL TOLL FREE +1 800 522 6752 (CONTINENTAL UNITED STATES AND PUERTO RICO ONLY) 

The 

Support Center

 offers a means of providing technical assistance when required. In addition, Field Service 

Specialists are available to provide assistance in the adjustment or repair of the application equipment when 
problems arise that your maintenance personnel cannot correct. 

INFORMATION REQUIRED WHEN CONTACTING THE SUPPORT CENTER 

When calling the Support Center regarding service to equipment a person familiar with the device should be 
present with a copy of the manual (and drawings) to receive instructions. Many difficulties can be avoided in 
this manner. 

When calling the Support Center, be ready with the following information: 

 

Customer name 

 

Customer address 

 

Person to contact (name, title, telephone 
number, and extension) 

 

Person calling 

 

Equipment number (and serial number, if 
applicable) 

 

Product part number (and serial number, if 
applicable) 

 

Urgency of request 

 

Nature of problem 

 

Description of inoperative components 

 

Additional information that may be helpful 

 

 

 

© Copyright 2023 TE Connectivity Ltd. family of companies. 

TE Connectivity, TE Connectivity (logo), and TE (logo) are trademarks. Other logos and product or 
company names may be trademarks of their respective owners. 

PRODUCT INFOR1 800 522 6752 

This controlled document is subject to change. 

For the latest revision and Regional Customer Service, visit our website at 

www.te.com

. 

Содержание 523199-3
















Отзывы: