manualshive.com logo in svg

TCS US4050, Руководство по настройке, Страница: 19 / 22

Поделиться
Скачать
TCS US4050 Скачать руководство пользователя страница 19

2800 Laura Lane  •  Middleton, WI 53562  |  800.288.9383  |  www.tcsbasys.com  

19

19

Configuration

About Section

Touching the ABOUT button on the bottom of the HOME screen brings up the About section. The main About screen 

displays the following information:

•  Model number
•  Device name
• 

Location (if set)

•  Device ID
•  Serial number
•  Firmware version
•  Hardware version

The display also features the TCS logo and TCS web site and support phone number. (The logo and support information is 

customizable. Contact TCS Technical Support for more information.)
Touching the TCS logo on the ABOUT screen will advance you to the second ABOUT screen, which contains the following 

information:

•  Bootloader version
•  Manufacture date
•  Last restart information
•  Sub-assembly serial number
•  Factory codes

Touching the TCS logo again will return you to the main ABOUT screen. Touching the HOME button will return you to the 

Home screen. 

About Section Main Screen

About Section Second Screen

Содержание US4050























Отзывы:

Нет отзывов