TC Electronic G-System Скачать руководство пользователя страница 53

Страница: 53 / 81

Tap Tempo: Hit Twice or More!

The Tap Tempo function allows you to tap the Global
tempo. Tap tempo is averaged from the first two taps and
up to the last ten.

Tap Tempo is always shown in both milliseconds (ms)
and beats per minute (BPM).

The interval between taps must not be shorter than
200ms or longer than 2000ms.

The Global Tapped Tempo is used to set the
corresponding tempo parameters in the relevant effect
pages (see the Effect section for more information).

In the Tempo menu, Encoders A and C can also be used
to adjust the tempo.

Hitting TAP TEMPO two times within two seconds
will initiate Tempo mode. Hit any other switch to
interrupt the tapping sequence.

>> EFFECT COPIED <<

EDIT A

EDIT B

EDIT C

>> PRESET STORED <<

EDIT A

EDIT B

EDIT C

BPM

TEMPO

TIME

638ms

EDIT A

EDIT B

EDIT C

TAP TEMPO

Содержание G-System


















































































Результаты поиска

Содержание G-System

Отзывы:

Похожие инструкции для G-System

Бренды по названию

Популярные бренды

TC Electronic G-System, Руководство пользователя

Результаты поиска

Содержание G-System

Отзывы:

Похожие инструкции для G-System

Бренды по названию

Популярные бренды