TC Electronic G-System Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 81

background image

Tremolo

Introduction

A Tremolo is basically a change of the signal level
controlled by an LFO. The G-System offers variations of
this effect; ranging from soft and smooth to hard and
aggressive.

Speed

Range: 0.050Hz to 20Hz
This parameter sets the speed of the effect.

Tempo

Range: Ignore, 2 to 1/32T (T= Triplet & D= Dotted)
When set to any value between 1 and 1/32T, the G-
System’s Global Tempo is subdivided according to this
setting. When set to “Ignore”, the speed set by the Speed
parameter is used instead.

The Tap Master parameter – located in the Utility
menu – specifies whether the

Global

tempo or the

tempo set by the Speed parameter in each preset
should be used at preset change.

Depth

Range: 0 to 100%
This parameter sets the intensity of the effect. A 100%
setting means that the signal is completely muted
between signal peaks.

Type

Range: Soft or Hard (Sinus or Square)
Two waveforms are available as modulation sources for
the Tremolo effect. Setting this parameter to Hard results
in a steeper effect. Listen and choose the appropriate
option.

Sine

Square

Width

Range: 0 to 100%
If you set this parameter e.g. to 20% with a Type setting
of Hard, the waveform will be on for 80% of one period.
With a Type setting of Soft, a 50% setting would yield a
full sine wave, whilst 0% and 100% would yield a crest-
to-peak and peak-to crest curve, respectively.

Pulsewidth

Hi-Cut

Range: 20Hz to 20kHz
This parameter attenuates the high frequencies of the
Tremolo effect. Use the hi-cut filter to create a less
dominant Tremolo effect without changing the effect’s
Depth.

OutLev – Out Level

Range: -100 to 0dB
This parameter sets the overall Output level of this effect.

Enable

Range: Off/On
The effect’s status. All settings are stored as part of the
preset even if this particular effect is disabled.

EFFECTS – MOD

63

«
...
63
64
65
66
67
...
»

Содержание G-System


















































































Отзывы:

Нет отзывов

Похожие инструкции для G-System

Бренд: Qingdao H.Y Страницы: 6

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

Бренд: XM Fitness Страницы: 10

Бренд: Raytec Страницы: 60

Бренд: UniPix Страницы: 24

Pendalyte 40472U

Бренд: Lightolier Страницы: 3

Бренд: Zodiac Страницы: 32

Бренд: GE Страницы: 2

R100 Swell Series

Бренд: WAVEFIT Страницы: 30

Бренд: Hameg Страницы: 39

Бренд: Teac Страницы: 1

Бренд: Garelick Страницы: 2

Бренд: EHEIM classic Страницы: 128

Бренд: Laguna Tools Страницы: 48

Бренд: B & D Electromedical Страницы: 43

Compact Power Lightset V2

Бренд: SHOWTEC Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды