TC Electronic G-System Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 81

background image

Using Expression Pedals to
Control Specific Parameters

Once the connected Expression/Volume pedals are
properly set up and calibrated as explained in the
previous section, it is time to define which parameters
they should control.

Basics

•

Press EDIT to enter Edit Mode.

•

Press ENTER two times. You can now access the
complete list of parameters in the current preset that
can be controlled via the connected pedals and
Encoders A, B and C.

The display now looks similar to this:

•

Use the INPUT Encoder to select the expression
pedal you want to setup. Note that Encoders A, B and
C also can be used as real-time controllers in Edit
Mode.

>> EFFECT COPIED <<

EDIT A

EDIT B

EDIT C

>> PRESET STORED <<

EDIT A

EDIT B

EDIT C

None-> Pitch Voice1
Min 0 Mid 50 Max 100

EDIT A

EDIT B

EDIT C

•

Vol: Refers to a pedal connected to the Vol
Connector on the GFX01’s rear panel or to the
Control Board’s Vol Connector.

•

Exp: Refers to a pedal connected to the Exp
Connector on the GFX01’s rear panel or to the
Control Board’s Exp Connector.

•

Enc A, Enc B and Enc C: Refers to Encoders A, B
and C when in Edit Mode.
Just like expression pedals connected to Vol or Exp,
the three Encoders A, B and C can also be assigned
and used to control pre-selected parameters.

•

Min, Mid and Max: Sets the value corresponding to
the Mid, Mid and Max position of the expression
pedal.

Example
Imagine that you have assigned Encoder A to control
Delay Feedback. This means that at the end of the solo
or song, you can perform that über-cool trick of
increasing the feedback to 100% for that special vintage,
non-stop-repeats “on-your-knees” effect.

Setting Up Enc A, B and C
Follow the exact same procedure as explained above in
“Using Expression Pedals to Control Specific
Parameters”. Note that you do not have to calibrate
Encoders A, B and C.

>> EFFECT COPIED <<

EDIT A

EDIT B

EDIT C

>> PRESET STORED <<

EDIT A

EDIT B

EDIT C

EDIT A

EDIT B

EDIT C

Exp.

Delay Delay

Min 0 Mid 50 Max100

MENU MODE – PEDALS

43

•

The LCD now reads “Set Max”.

•

Place your pedal in maximum position (“Toe down”)
and press ENTER.

•

The LCD reads: “CALIBRATION DONE”.

«
...
43
44
45
46
47
...
»

Содержание G-System


















































































Отзывы:

Нет отзывов

Похожие инструкции для G-System

ACS880-01 Series

Бренд: ABB Страницы: 238

Бренд: FEAS Страницы: 72

Бренд: AAON Страницы: 36

Бренд: B-K lighting Страницы: 3

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: Launch Страницы: 3

Бренд: Launch Страницы: 43

Бренд: Launch Страницы: 8

Бренд: Launch Страницы: 67

Бренд: Launch Страницы: 55

Бренд: LAUNCH TECH Страницы: 14

X-431 PROS V4.0

Бренд: Launch Страницы: 80

Бренд: MAHA Страницы: 21

Бренд: MAGUIRE Страницы: 47

Бренд: Yamaha Страницы: 48

Бренд: Fast Страницы: 60

Бренд: Aveo Engineering Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды